40108 75 Mariner SCREW (M10 X .75)


40108 75 SCREW (M10 X .75) Mariner 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB SCREW

Buy SCREW (M10 X .75) 40108 75 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 11
 

Mariner entire parts catalog list:

7031203GD 1998,1999
7031207CD 1994,1995,1996,1997,1998
7031207LF 2002,2003
7031312TB 2005,2006
7041203GB 1998,1999,2000,2001,2002,2003,2004
70432037D 1997,1998
7043213HD 1999,2000,2001,2002,2003,2004
7043213TD 2005
7043302TD 2005
7043412TB 2005,2006
7043412TD 2005
7050312TB 2005
7050312UB 2006
7050412TB 2005
7050412TD 2005
7050412UB 2006

Information:


Table 1
Diagnostic Codes Table for the DEF Tank Sensor
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
1761-3 3130-3 Aftertreatment 1 Diesel Exhaust Fluid Tank Level : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
1761-4 3130-4 Aftertreatment 1 Diesel Exhaust Fluid Tank Level : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
3031-3 3134-3 Aftertreatment 1 Diesel Exhaust Fluid Tank Temperature : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged.
3031-4 3134-4 Aftertreatment 1 Diesel Exhaust Fluid Tank Temperature : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The code is logged. The 5 VDC signal for the Diesel Exhaust Fluid (DEF) tank level sensor is routed to terminal 1 of the tank header unit. The 5 VDC signal for the DEF tank temperature sensor is routed to terminal 3 of the tank header unit. The sensor return is shared and is routed to terminal 2 of the tank header unit. The ECM provides short circuit protection for the internal power supply. A short circuit to the battery will not damage the internal power supply.Note: The tank header unit houses the DEF tank temperature and the DEF tank level sensors. The sensors are not serviceable individually.
Illustration 1 g03811036
Schematic diagram for the DEF tank header
Illustration 2 g03811042
(1) DEF level signal
(2) Sensor return
(3) DEF temperature signal Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Diagnostic Codes
A. Establish communication between the electronic service tool and the DEF Control Unit (DCU) . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Turn the keyswitch to the ON position.
C. Check for "-3" or " -4" active or logged codes.
Diagnostic code
Result: A -3 diagnostic code is active.
Proceed to Test Step 2.
Result: A -4 diagnostic code is active.
Proceed to Test Step 3.
2. Create a Short at the Sensor Connector
A. Verify that the harness connector is free of debris, free of corrosion and securely connected.
B. Install a jumper wire between the appropriate signal and return wire at the sensor connector in order to create a short. Refer to Illustration 2.
C. Turn the keyswitch to the ON position.
D. Monitor the diagnostic codes on the electronic service tool. Check for an active -4 diagnostic code for the suspect sensor.
E. Turn the keyswitch to the OFF position.
Short created
Result: A -4 diagnostic code became active after creating the short at the sensor connector. The wiring is OK.
Repair: Replace the DEF tank header assembly. Refer to the Disassembly and Assembly manual.
Verify that the fault is resolved by cycling the keyswitch to the OFF position for 2 minutes. Turn to the keyswitch to the ON position and check for active codes.
Result: A -4 diagnostic code does not become active for the tank header unit.
Repair: Repair or replace the wiring harness.
Verify that the fault is resolved by cycling the keyswitch to the OFF position for 2 minutes. Turn to the keyswitch to the ON position and check for active codes.
If the fault is still present, contact the Dealer Solutions Network (DSN).
3. Create an Open at the Suspect Sensor Connector
A. Disconnect the connector for the tank header unit.
B. Turn the keyswitch to the ON position.
C. Monitor the diagnostic codes on the electronic service tool. Check for an active -3 diagnostic code for the suspect sensor.
D. Turn the keyswitch to the OFF position.
Create an open
Result: A -3 diagnostic code became active after disconnecting the sensor. The wiring is OK.
Repair: Replace the DEF tank header assembly. Refer to the Disassembly and Assembly manual.
Verify that the fault is resolved by cycling the keyswitch to the OFF position for 2 minutes. Turn to the keyswitch to the ON position and check for active codes.
Result: A -3 diagnostic code does not became active after disconnecting the sensor.
Repair: Repair or replace the wiring harness.
Verify that the fault is resolved by cycling the keyswitch to the OFF position for 2 minutes. Turn to the keyswitch to the ON position and check for active codes.
If the fault is still present, contact the Dealer Solutions Network (DSN).


Parts screw Mariner:

40001 71
 
40001 71 SCREW, CONTROL PLATFORM (16MM)
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 7020207, 7031203GD, 7031207CD, 70432037D, 7050302ED, 7050412YD, 7055207GD, 7060412ET, 7075217CD, 7075312ND, 7075312SD, 7075717, 7100412CD, 7100412NC
40011131
 
40011131 SCREW, DRIVE SHAFT HOUSING TO PLATE
7006201CD, 7008218EW, 7008237, 7010312DT, 70152374D, 7016207CD, 7020201NC, 7031203GD, 7031207CD, 7075D73UY, 7075D73ZY, 7090D73RD, 7F08203HF, 7F08261DF, 7F25201GD, 7F25203JB, 7F25203LB
40011107
SCREW, HOUSING TO ADAPTOR PLATE (16MM)
40011107 SCREW, HOUSING TO ADAPTOR PLATE (16MM)
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD,
12896
 
12896 SCREW, SWITCH
7031203GD, 7031207CD, 70404119D, 7050302ED, 7050412YD, 7060412ET, 7075217CD, 7075312ND, 7075312SD, 7075717, 7100412NC, 7225412CD
40019 87
 
40019 87 SCREW, COVER TO SEPARATOR
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7115473JD, 7135473GD, 7135473HD, 7135473KD, 7175413AD, 7175413PD, 7175413YD, 7200473FD, 7200473GD, 7200473HD, 7220727
40106 30
 
40106 30 SCREW, (M6 x 30), Oil Warning Module
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412U
808612
SCREW, FUEL BOWL
808612 SCREW, FUEL BOWL
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412E
821919 16
 
821919 16 SCREW, (M5 x 14) (Self-Threading)
7016207CD, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB
Back to top