49908 SCREW, PINION GEAR Mariner
70152374D, 7020201HB, 7020201NC, 7020201TB, 7020207, 7B25201GF
SCREW
Price: query
Rating:
Mariner entire parts catalog list:
7020201HB 1999,2000,2001,2002,2003,2004
7020201NC 1988,1989,1990,1991,1992,1993,1994
- GEAR HOUSING(DRIVESHAFT) » 49908
7020207 1977,1984,1985,1986,1987
- GEAR HOUSING (DRIVER SHAFT) » 49908
Information:
1. Disconnect elbow (1) from the oil pump. 2. Remove bolts (2) and locks that hold the oil pump in position.3. Remove the oil pump (3). The weight of the oil pump is 35 lb. (16 kg).Install Oil Pump
1. Put the No. 1 piston on top center compression stroke.2. Turn both balancer shafts until the flat part is away from the oil pan plate. Install two 3/8"-16 NC bolts 1 1/2" long through the oil pan plate into the holes in the balancer shafts. This will prevent balancer shaft movement. Do not tighten the two bolts (1) against the bottom of the countersunk holes in the balancer shafts. 3. Put the oil pump (2) in position on the engine block. Install the bolts and locks that hold the oil pump in position.4. Remove bolts (1). Check to see that the balancer shaft timing is correct. Balancer shaft timing is correct when the holes in the balancer shafts are in alignment with the holes in the oil pan plate and No. 1 piston is at top center compression stroke.5. Connect the suction tube elbow to the oil pump.end by:a) install oil panDisassemble Oil Pump
start by:a) remove oil pump1. Remove the idler gear from the oil pump. 2. Remove bell assembly (3) from the oil pump.3. Remove three bolts (1) from body (2). Remove the body. 4. Remove two bearings (4) from the body. 5. Remove the bolt and washer that hold the drive gear (5) on the oil pump. Use tool (A) to remove drive gear (5) from the shaft.6. Remove the key from the shaft.7. Remove the bushing from the drive gear. 8. Remove gear (7) from the shaft.9. Remove shaft assembly (8) and spacer (6). 10. Remove gear (9) from the shaft assembly. Remove the shaft assembly from the spacer and the key from the shaft. 11. Remove shaft assembly (12) from the body.12. Remove two bearings (10) from the body.13. Remove bolt (11) from cover (13). Remove the cover and valve assembly from the body.Assemble Oil Pump
1. Use tool (A) to install the two bearings (1) in the body.2. Put the valve assembly (2) in position in the body. Install the cover and bolt. 3. Put clean SAE 30 oil on the bearings in the body and the shaft assembly (3). Install the shaft assembly into the body. 4. Put shaft assembly (4) in spacer (5). Install the key in the shaft assembly. Install gear (6). Put the shaft assembly and spacer in position in the body. 5. Install gear (7) on the shaft.6. Use tool (A) to install a new bushing in the drive gear. 7. Put drive gear (8) in position on the shaft. Install the bolt and washer that hold the drive gear in position on the oil pump. 8. Use tool (A) to install the two bearings in the body.9. Put body (9) in position on the oil pump. Install the three bolts that hold the body in position.10. Put clean SAE 30 oil in the oil pump. The pump must turn free by hand.end by:a) install oil pump
1. Put the No. 1 piston on top center compression stroke.2. Turn both balancer shafts until the flat part is away from the oil pan plate. Install two 3/8"-16 NC bolts 1 1/2" long through the oil pan plate into the holes in the balancer shafts. This will prevent balancer shaft movement. Do not tighten the two bolts (1) against the bottom of the countersunk holes in the balancer shafts. 3. Put the oil pump (2) in position on the engine block. Install the bolts and locks that hold the oil pump in position.4. Remove bolts (1). Check to see that the balancer shaft timing is correct. Balancer shaft timing is correct when the holes in the balancer shafts are in alignment with the holes in the oil pan plate and No. 1 piston is at top center compression stroke.5. Connect the suction tube elbow to the oil pump.end by:a) install oil panDisassemble Oil Pump
start by:a) remove oil pump1. Remove the idler gear from the oil pump. 2. Remove bell assembly (3) from the oil pump.3. Remove three bolts (1) from body (2). Remove the body. 4. Remove two bearings (4) from the body. 5. Remove the bolt and washer that hold the drive gear (5) on the oil pump. Use tool (A) to remove drive gear (5) from the shaft.6. Remove the key from the shaft.7. Remove the bushing from the drive gear. 8. Remove gear (7) from the shaft.9. Remove shaft assembly (8) and spacer (6). 10. Remove gear (9) from the shaft assembly. Remove the shaft assembly from the spacer and the key from the shaft. 11. Remove shaft assembly (12) from the body.12. Remove two bearings (10) from the body.13. Remove bolt (11) from cover (13). Remove the cover and valve assembly from the body.Assemble Oil Pump
1. Use tool (A) to install the two bearings (1) in the body.2. Put the valve assembly (2) in position in the body. Install the cover and bolt. 3. Put clean SAE 30 oil on the bearings in the body and the shaft assembly (3). Install the shaft assembly into the body. 4. Put shaft assembly (4) in spacer (5). Install the key in the shaft assembly. Install gear (6). Put the shaft assembly and spacer in position in the body. 5. Install gear (7) on the shaft.6. Use tool (A) to install a new bushing in the drive gear. 7. Put drive gear (8) in position on the shaft. Install the bolt and washer that hold the drive gear in position on the oil pump. 8. Use tool (A) to install the two bearings in the body.9. Put body (9) in position on the oil pump. Install the three bolts that hold the body in position.10. Put clean SAE 30 oil in the oil pump. The pump must turn free by hand.end by:a) install oil pump
Parts screw Mariner:
92799
92799 SCREW
7002201DK, 7008237, 7020201NC, 7020207, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135473KD, 7135D73RD, 7135D73UY, 7135D73ZY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7
40001209
40001209 SCREW, CRANKCASE TO CYLINDER BLOCK (60MM)
70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB, 7020207
67892
67892 SCREW, DRAIN - MAGNETIC
7002201DK, 7008237, 7016207CD, 7020207, 7045217, 7050200, 7050412YD, 7050716, 7050717, 7060312PC, 7060412ET, 7060524, 7070509, 7070520, 7075312ND, 7075312SD, 7075524, 7075717, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7100412NC, 7115520,
40057111
1859
42125 1
42125 1 SCREW, CRANKCASE TO CYLINDER BLOCK
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7020201HB, 7020201NC, 7020201TB
40011107
40011107 SCREW, HOUSING TO ADAPTOR PLATE (16MM)
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201NC, 7020201TB, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD,
814945
814945 SCREW, (.312-18 x 3.500), CLAMP BRACKET TO TRANSOM
70152374D, 7020201HB, 7020201NC, 7020201TB, 7F08201TB, 7F10203HD, 7F13203UB, 7F15201GD