66023 Mariner SCREW, ADAPTOR PLATE TO HOUSING PLATE (2")


66023 SCREW, ADAPTOR PLATE TO HOUSING PLATE (2") Mariner 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629, 7150629, 7175629 SCREW
66023 SCREW, ADAPTOR PLATE TO HOUSING PLATE (2") Mariner
Rating:
63

Buy SCREW, ADAPTOR PLATE TO HOUSING PLATE (2") 66023 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Mariner entire parts catalog list:

7075524 1984,1985,1986
7080508 1978,1979
7080629 1979,1980
7085507 1977
7090520 1980
7090524 1984,1985,1986,1987,1988
7090529 1979
7115520 1980
7115528 1978
7115529 1979
7140528 1978,1979
7140629 1979
7150629 1979,1980,1982,1984,1985
7175629 1979,1980,1985,1986,1988

Information:


Table 1
Specifications for 356-1119 Manifold and 356-1124 Exhaust Manifold Gp    
Callout     Part Number     Part Name     Specification Description    
15     238-8292     Bolt     Torque to...................
44 N m (32 lb ft)
Tighten the bolts in the sequence that is in illustration 4.    Removal Procedure
Start By:
Remove the turbocharger for top mounted turbocharged engine. Refer to Disassembly and Assembly, "Turbocharger (Top Mounted Turbocharger)" for the correct procedure.
Remove the turbocharger for side mounted turbocharged engine. Refer to Disassembly and Assembly, "Turbocharger (Side Mounted Turbocharger)" for the correct procedure.
Illustration 1 g02478716
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Remove bolts (2) and bolt (9) from tube assembly (3) .
Remove tube assembly (3) from the cylinder head and the exhaust cooler.
Remove gasket (1) (not shown) and gasket (10) (not shown) from tube assembly (3) .
Prior to and during removal of bolts (6) and bolts (11) apply releasing fluid to the bolts. Remove bolts (6) and bolts (11) from tube assembly (8) .
Remove tube assembly (8) from the exhaust cooler and the exhaust manifold.
Remove gasket (7) (not shown) and gasket (12) (not shown) from tube assembly (8) .
Remove bolt (5) and bolt (13) from dipstick tube assembly (4) .
Loosen nut (14) on dipstick tube assembly (4). Remove the dipstick tube assembly.
Remove O-ring seal (15) (not shown) and seal (16) (not shown) from the dipstick tube assembly.
Illustration 2 g02477641
Tighten sequence of exhaust manifold
Illustration 3 g02478717
Loosen bolts (15) in reverse numerical order. Refer to Illustration 2.Note: Loosen the bolts in reverse numerical order will help prevent distortion of the exhaust manifold.
Remove bolts (15) and spacers (16) from exhaust manifold (17). Note position of the different length spacer.Note: Support the manifold as the bolts are removed.
Remove exhaust manifold (17) .
Remove exhaust manifold gasket (18) (not shown).Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     366-1820     Manifold Alignment Pins     2    
B     377-2038     Manifold Alignment Pins     1    
C     -     Loctite 575     1    
Ensure that the exhaust manifold is clean and free from damage. If necessary, replace the exhaust manifold. Clean the gasket surface of the cylinder head.
Illustration 4 g02477697
Tighten sequence of exhaust manifold and Tooling position
Illustration 5 g02478717
Position a new exhaust manifold gasket (18) (not shown) onto the cylinder head. Install Tooling (A) in Positions (X) and Tooling (B) in Positions (Y). Refer to Illustration 4.Note: Ensure that the exhaust manifold gasket is correctly oriented.
Align exhaust manifold (17) with Tooling (A) and Tooling (B). Install the exhaust manifold to the cylinder head.
If bolts (15) have been previously used, thoroughly clean the bolts. Tooling (C) should be applied to the first two threads of the bolts.Note: Do not apply Tooling (C) to new bolts.
Install bolts (15) and spacers (16) hand tight. Ensure that the different length spacer is installed into the correct position.
Remove Tooling (A) and Tooling (B). Install remaining bolts (15) and spacers (16) hand tight.
Tighten bolts (15) to a torque of 44 N m (32 lb ft). Tighten the bolts in the sequence that is shown in Illustration 4.
Illustration 6 g02478716
Ensure that all tube assemblies are free from restriction and damage.
Position a new gasket (7) (not shown) and a gasket (12) (not shown) onto tube assembly (8) .
Install tube assembly (8) onto the exhaust cooler and the exhaust manifold.
Install bolts (6) and bolts (11) to tube assembly (8). Tighten the bolts to a torque of 22 N m (195 lb in).
Position a new gasket (1) (not shown) a new gasket (10) (not shown) o


Parts screw Mariner:

62568
 
62568 SCREW, FUEL GAUGE
7001200, 7004201, 7005201, 7005207, 7005227, 7006201CD, 7006201HB, 7008204, 7008208, 7008218EW, 7008226, 7008237, 7008238, 7008247, 7008248, 7008305, 7010207HB, 7010209, 7010312DT, 7015201LD, 7015207, 70152374D, 7015307, 7015327, 7015529, 7020201, 70
22968
 
22968 SCREW, CENTER MAIN BEARING CLAMPING
7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
30225
 
30225 SCREW, END CAP MOUNTING (1")
7080508, 7085507, 7115473JD, 7135473KD, 7150423JD, 7200413JD
46378
 
46378 SCREW, RETAINER TO CYLINDER BLOCK COVER (1")
7075524, 7080508, 7080629, 7085507
28200
 
28200 SCREW, STRAP STOP TO HOUSING (3 7/8")
7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
34676
 
34676 SCREW, THROTTLE LEVER TO NEUTRAL WARM-UP LEVER
7080508, 7090529, 7115528, 7115529, 7140528, 7140629
4542
 
4542 SCREW, PLUG - MAIN NOZZLE
7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
68554
 
68554 SCREW, PULLEY CLAMPING
7115528, 7115529, 7140528, 7140629
Back to top