69093 Mariner SCREW, AIR MANIFOLD TO SOUND ATTENUATOR


69093 SCREW, AIR MANIFOLD TO SOUND ATTENUATOR Mariner 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200620, 7220727 SCREW
69093 SCREW, AIR MANIFOLD TO SOUND ATTENUATOR Mariner
Rating:
23

Buy SCREW, AIR MANIFOLD TO SOUND ATTENUATOR 69093 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Mariner entire parts catalog list:

7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070509 1979
7070520 1980,1982,1983
7135417PD 1989
7135826 1986,1987,1988
7150453ND 1988
7150453PD 1989,1990
7150629 1979,1980,1982,1984,1985
7175412PD 1989
7175629 1979,1980,1985,1986,1988
7200620 1980,1982,1983,1984,1985,1986,1988
7220727 1987,1988

Information:


Table 1
Diagnostic Trouble Codes for the Valve Position Sensors    
CDL Code    Description    Notes    
3407-3     EGR Valve Position Sensor : Voltage Above Normal     The Electronic Control Module (ECM) detects the following conditions:
The signal voltage from the position sensor on the NOx Reduction System (NRS) valve is greater than 4.8 VDC for 0.1 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code. The NRS valve will be fully closed while the code is active.
The engine will be derated.    
3407-4     EGR Valve Position Sensor : Voltage Below Normal     The ECM detects the following conditions:
The signal voltage from the NRS valve position sensor is less than 0.2 VDC for 0.1 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code. The NRS valve will be fully open while the code is active.
The engine will be derated.    
3515-3     Engine Throttle Actuator Position Sensor : Voltage Above Normal     The ECM detects the following conditions:
The signal voltage from the position sensor on the engine intake throttle valve is greater than 4.8 VDC for 0.1 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code. The engine intake throttle valve will be fully closed while the code is active.
The engine will be derated.    
3515-4     Engine Throttle Actuator Position Sensor : Voltage Below Normal     The ECM detects the following conditions:
The signal voltage from the position sensor on the engine intake throttle valve is less than 0.2 VDC for 0.1 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code. The engine intake throttle valve will be fully closed while the code is active.
The engine will be derated.    
2490-3     ARD Air Pressure Control Actuator Position Sensor : Voltage Above Normal     The ECM detects the following conditions:
The signal voltage from the position sensor on the combustion air valve is greater than 4.85 VDC for 8 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code.
The engine will be derated.    
2490-4     ARD Air Pressure Control Actuator Position Sensor : Voltage Below Normal     The ECM detects the following conditions:
The signal voltage from the position sensor on the combustion air valve is less than 0.2 VDC for 8 seconds.
If equipped, the warning lamp will come on. The ECM will log the diagnostic code.
The engine will be derated.    The following conditions must exist before any of the preceding codes will become active:
The ECM has been powered for at least 2 seconds.
There are no active 262 codes.
There are no active 168 codes.Use this procedure in order to troubleshoot the position sensors for the following valves:
NRS valve
Engine intake throttle valve
Combustion air valve for the Aftertreatment Regeneration Device (ARD)Each position sensor is integral in the associated valve. If the following procedure indicates a fault with the position sensor, then the entire valve must be replaced.The following background information is related to this procedure:The troubleshooting procedures for the diagnostic codes of each position sensor are identical. The 5 VDC sensor supply provides power to all 5 VDC sensors. The ECM supplies 5.0 VDC to terminal "5" of the engine intake throttle valve connector and to terminal "1" of the other valve connectors. The sensor common from the ECM connector goes to terminal "3" of the engine intake throttle valve connector. The sensor common from the ECM connector goes to terminal "2" of the other valve connectors. The sensor supply is output short circuit protected. A short circuit to the battery will not damage the circuit inside the ECM. The signal voltage from terminal "4" of the engine intake throttle valve is supplied to the appropriate terminal at the P2 ECM connector. The signal voltage from terminal "3" of the other valves is supplied to the appropriate terminal at the P2 ECM connector.Pull-up VoltageThe ECM continuously outputs a pull-up voltage on the circuit for the sensor signal wire. The ECM uses this pull-up voltage in order to detect an open in the signal circuit. When the ECM detects a voltage above a threshold on the signal circuit, the ECM generates an open circuit diagnostic code (XXXX-3) for the sensor.If the sensor is disconnected, pull-up voltage at the sensor connector indicates that the wires are not open or shorted to ground. If the sensor is disconnected, the absence of pull-up voltage indicates an open in the signal wire or a short to ground. If the sensor is disconnected and the voltage is different from pull-up voltage, the signal wire is shorted to another wire in the harness.
Illustration 1 g02186415
Typical example of the schematic for the position sensors
Illustration 2 g01981373
Typical view of the pin locations on the P2 connector for the position sensors (3) Engine intake throttle valve position sensor signal (15) NRS valve position sensor signal (16) Combustion air valve position sensor signal (45) Combustion air valve position sensor 5 VDC supply (46) Engine intake throttle valve, NRS valve position sensors 5 VDC supply (55) Combustion air valve position sensor ground (56) Engine intake throttle valve, NRS valve position sensors ground
Illustration 3 g02186473
Typical view of the pin locations for the valve position sensors on the connectors from the engine to the Clean Emissions Module (CEM) (1) 5 VDC supply (2) Combustion air valve position sensor ground (9) Combustion air valve position sensor signal
Illustration 4 g01955200
Typical example of the connector for the combustion air valve (1) 5 VDC supply (2) Position sensor ground (3) Position sensor signal
Illustration 5 g02157941
Typical example of the connector for the engine intake throttle valve (3) Position sensor ground (4) Position sensor signal (5) 5 VDC supply
Illustration 6 g02854698
Typical example of the connector for the NRS valve (1) 5 VDC supply (2) Position sensor ground (3) Position sensor signal


Parts screw Mariner:

49318
 
49318 SCREW, UPPER MOUNT ( 5 1/2")
7070509, 7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
30902
 
30902 SCREW, SAFETY SWITCH TO CONTROL HOUSING
7070509, 7080508, 7090529, 7115528, 7115529, 7140528, 7140629
4541
 
4541 SCREW, PLUG - MAIN FUEL JET CHANNEL
7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7135417PD, 7135826, 7140528, 7140629, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200412PD, 7200620
33524
 
33524 SCREW, CHOKE SOLENOID ATTACHING (5/8")
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
75794
 
75794 SCREW, HINGE BRACKET TO REAR BRACKET- UPPER (1 1/8")
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
36154
 
36154 SCREW, ADAPTOR TO SOUND ATTENUATOR (1 1/4")
7070509, 7075312ND, 7075312SD, 7075524, 7075717, 7080629, 7090520, 7090524, 7115520
75162
 
75162 SCREW
7150629, 7175629, 7200620, 7250422PD
66725
 
66725 SCREW, (.375-16 x 3.50)
7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135473KD, 7135826, 7135D73RD, 7135D73UY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7150453ND, 7150453PD,
Back to top