70602 Mariner SCREW, PLATE/MANIFOLD COVER MOUNTING (2")


70602 SCREW, PLATE/MANIFOLD COVER MOUNTING (2") Mariner 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520 SCREW
70602 SCREW, PLATE/MANIFOLD COVER MOUNTING (2") Mariner
Rating:
58

Buy SCREW, PLATE/MANIFOLD COVER MOUNTING (2") 70602 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Compatible models:

Mariner entire parts catalog list:

7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989
7060524 1984,1985,1986,1989,1990
7070509 1979
7070520 1980,1982,1983

Information:


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed with the draining cold oil. Drain the crankcase with the engine stopped. Drain the crankcase with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will cause the waste particles to be recirculated through the engine lubrication system with the new oil.Drain the Engine Oil
After the engine has been run at the normal operating temperature, stop the engine. Use one of the following methods to drain the engine crankcase oil:
If the engine is equipped with a manual sump pump, turn the drain valve knob counterclockwise in order to pump the oil out of the oil pan. After the oil has drained, turn the drain valve knob clockwise in order to close the drain valve.
If the engine is not equipped with a drain valve, remove the oil drain plug in order to allow the oil to drain. If the engine is equipped with a shallow sump, remove the bottom oil drain plugs from both ends of the oil pan.After the oil has drained, the oil drain plugs should be cleaned and installed. Tighten the oil drain plugs to 70 14 N m (50 10 lb ft).Replace the Oil Filter
Caterpillar oil filters are built to Caterpillar specifications. Use of an oil filter not recommended by Caterpillar could result in severe engine damage to the engine bearings, crankshaft, etc., as a result of the larger waste particles from unfiltered oil entering the engine lubricating system. Only use oil filters recommended by Caterpillar.
Remove the oil filter with a 1U-8760 Chain Wrench.
Cut the oil filter open with a 175-7546 Oil Filter Cutter. Break apart the pleats and inspect the oil filter for metal debris. An excessive amount of metal debris in the oil filter may indicate early wear or a pending failure. Use a magnet to differentiate between the ferrous metals and the nonferrous metals that are found in the oil filter element. Ferrous metals may indicate wear on the steel and cast iron parts of the engine.Nonferrous metals may indicate wear on the aluminum parts, brass parts or bronze parts of the engine. Parts that may be affected include the following items: main bearings, rod bearings, turbocharger bearings and cylinder heads.Due to normal wear and friction, it is not uncommon to find small amounts of debris in the oil filter. Consult your Caterpillar dealer in order to arrange for a further analysis if an excessive amount of debris is found in the oil filter.
Illustration 1 g00103713
Typical filter mounting base and filter gasket
Clean the sealing surface of the filter mounting base. Ensure that all of the old oil filter gasket is removed.
Apply clean engine oil to the new oil filter gasket.
Do not fill the oil filters with oil before installing them. This oil would not be filtered and could be contaminated. Contaminated oil can cause accelerated wear to engine components.
Install the oil filter. Tighten the oil filter until the oil filter gasket contacts the base. Tighten the oil filter by hand according to the instructions that are shown on the oil filter. Do not overtighten the oil filter. Fill the Engine Crankcase
Remove the oil filler cap. Refer to the Operation and Maintenance Manual, "Refill Capacities and Recommendations" for more information on lubricant specifications. Fill the crankcase with the proper amount of oil.
If equipped with an auxiliary oil filter or system, extra oil must be added when filling the crankcase. Follow the OEM or filter manufacturer's recommendations. If the extra oil is not added, the engine may starve for oil.
To help prevent crankshaft or bearing damage, crank engine to fill all filters before starting. Do not crank engine for more than 30 seconds.
Start the engine and run the engine at "LOW IDLE" for two minutes. Perform this procedure in order to ensure that the lubrication system has oil and that the oil filters are filled. Inspect the oil filter for oil leaks.
Stop the engine and allow the oil to drain back to the sump for a minimum of ten minutes.
Remove the oil level gauge in order to check the oil level. Maintain the oil level between the "ADD" and "FULL" marks on the oil level gauge.


Parts screw Mariner:

21140
 
21140 SCREW, (.250-28 x .50), BRACKET TO PUMP
7050200, 7050716, 7060507, 7060528, 7070520, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
49318
 
49318 SCREW, UPPER MOUNT ( 5 1/2")
7070509, 7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
30902
 
30902 SCREW, SAFETY SWITCH TO CONTROL HOUSING
7070509, 7080508, 7090529, 7115528, 7115529, 7140528, 7140629
33524
 
33524 SCREW, CHOKE SOLENOID ATTACHING (5/8")
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
75794
 
75794 SCREW, HINGE BRACKET TO REAR BRACKET- UPPER (1 1/8")
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
36154
 
36154 SCREW, ADAPTOR TO SOUND ATTENUATOR (1 1/4")
7070509, 7075312ND, 7075312SD, 7075524, 7075717, 7080629, 7090520, 7090524, 7115520
9025
78495 1
 
78495 1 SCREW, WASHER TO THUMB SCREW
7001804, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524
Back to top