71796 Mariner SCREW, CYLINDER TO LOWER PIN


71796 SCREW, CYLINDER TO LOWER PIN Mariner 7060507, 7060528 SCREW
71796 SCREW, CYLINDER TO LOWER PIN Mariner
Rating:
88

Buy SCREW, CYLINDER TO LOWER PIN 71796 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 72
 

Compatible models:

7060507   7060528   Mariner

Mariner entire parts catalog list:

7060507 1977
7060528 1978

Information:


Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06102111
Typical example
Illustration 2 g06102122
Typical example
Disconnect harness assembly (1) from exhaust gas recirculation valve (2).
Remove bolts (3) from tube assembly (5). Support the exhaust gas recirculation valve as bolts (3) are removed.
Remove exhaust gas recirculation valve (2) from the inlet manifold.
Remove gasket (4) (not shown) and gasket (9) (not shown).
If necessary, remove bolts (6) and remove tube assembly (5) from exhaust cooler (NRS) (7) and exhaust gas recirculation valve (2).
Remove gasket (8) (not shown).Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-5598 Anti-Seize Compound 1
Sulfuric Acid Burn Hazard may cause serious personal injury or death.The exhaust gas cooler may contain a small amount of sulfuric acid. The use of fuel with sulfur levels greater than 15 ppm may increase the amount of sulfuric acid formed. The sulfuric acid may spill from the cooler during service of the engine. The sulfuric acid will burn the eyes, skin and clothing on contact. Always wear the appropriate personal protective equipment (PPE) that is noted on a material safety data sheet (MSDS) for sulfuric acid. Always follow the directions for first aid that are noted on a material safety data sheet (MSDS) for sulfuric acid.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Inspect the airways of the exhaust gas recirculation valve for deposits and debris. Use a suitable clean lint free cloth with a suitable engine cleaner to clean the deposits and debris out of the exhaust gas recirculation valve.
Illustration 3 g06102111
Typical example
Illustration 4 g06102122
Typical example
Clean the gasket surface's of exhaust gas recirculation valve (2).
Ensure that tube assembly (5) is clean and free from restriction, wear, and damage. If necessary, replace the tube assembly.
Position a new gasket (9) (not shown) onto exhaust gas recirculation valve (2). Ensure that the gasket is correctly orientated.
Position exhaust gas recirculation valve (2) onto the inlet manifold.
Position a new gasket (4) (not shown) between tube assembly (5) and exhaust gas recirculation valve (2).
Apply Tooling (A) to the threads of bolts (3).
Position tube assembly (5) onto exhaust cooler (NRS) (7).
Loosely install bolts (3) to tube assembly (5).
Position a new gasket (8) (not shown) onto tube assembly (5).
Position tube assembly (1) onto exhaust cooler (NRS) (7).
Apply Tooling (A) to the threads bolts (6).
Loosely install bolts (6) to tube assembly (5).
Tighten bolts (3) and bolts (6) to a torque of 25 N m (221 lb in). Ensure that tube assembly (5) is not strained as the bolts are tightened.
Connect harness assembly (1) to exhaust gas recirculation valve (2).
After replacement of the exh


Parts screw Mariner:

82487M
 
82487M SCREW
7010209, 7015529, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7040202, 7040207, 7040208, 7040507, 7040716, 7055524, 7060507, 7060522, 7060528
81292M
 
81292M SCREW, PLUG
7040207, 7040208, 7040328, 7040507, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
81279M
 
81279M SCREW, PLUG
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060528
82980M
 
82980M SCREW, TERMINAL STRIP ATTACHING
7048207, 7048227, 7048321, 7055524, 7060507, 7060522, 7060528, 7F08203HF, 7F08261DF
82798M
 
82798M SCREW
7048207, 7048227, 7048321, 7055524, 7060507, 7060528
97080M
 
97080M SCREW, PLUG
7048227, 7048321, 7060507, 7060522
84946M
 
84946M SCREW
7010209, 7015529, 7020201, 7025200, 7025500, 7040202, 7040208, 7040328, 7040507, 7040716, 7055524, 7060507, 7060522
71797
Back to top