76156 SCREW, (#10-32 x 1.88) Mariner
7150629, 7175629, 7200620
SCREW
Price: query
Rating:
Mariner entire parts catalog list:
7175629 1979,1980,1985,1986,1988
7200620 1980,1982,1983,1984,1985,1986,1988
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Piston Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear or damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g01244067
Illustration 2 g01155119
If the original piston is assembled, follow Step 2.a through Step 2.e in order to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Use Tooling (B) to install oil control ring (3) over the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward.
Position the piston ring gaps at 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
If the connecting rod assembly or the bush for the piston pin have been replaced, ensure that the height grade of the connecting rod is correct. Refer to Specifications, "Connecting Rods" for further information.
Lubricate bush (7) and lubricate the bore for the piston pin in piston (4) with clean engine oil.
Illustration 3 g01244172
Place the piston on a suitable surface with the crown downward. Install connecting rod (6) and piston pin (8) to piston (4). Ensure that square boss (13) on the piston, and forged Mark (X) on the connecting rod are in the correct position. See illustration 3. Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Illustration 4 g01244068
Illustration 5 g01001160
Aligning the connecting rod bearing in the center of the connecting rod
Install the upper half of connecting rod bearing (9) to connecting rod (6). Ensure that the connecting rod bearing is centralized in the connecting rod. Refer to Illustration 5. Note: New connecting rod bearings are supplied with an alignment tool. If new connecting rod bearings are installed, use the tool to align the connecting rod bearing in the connecting rod.
Install the lower half of connecting rod bearing (10) to connecting rod cap (11). Ensure that the connecting rod bearing is centralized in the connecting rod cap. Refer to Illustration 5. Note: New connecting rod bearings are supplied with an alignment tool. If new connecting rod bearings are installed, use the tool to align the connecting rod bearing in the connecting rod cap.
Repeat Step 2 through Step 8 for the remaining piston and connecting rod assemblies. Note: Fracture split connecting rods should not be left without the connecting rod caps installed. After the assembly procedure for the piston and connecting rod is completed, carry out the installation procedure as soon as possible.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install".
Parts screw Mariner:
14000
14000 SCREW, LINK ROD
7002201DK, 70152374D, 7020201HB, 7020201NC, 7020207, 70404119D, 7045217, 7050717, 7060312PC, 7075217CD, 7075217HD, 7075312ND, 7075312SD, 7075524, 7075717, 7090524, 7100412CD, 7100412NC, 7115473JD, 7115520, 71354120D, 7135412AD, 7135412ED, 7135412HD,
56500
56500 SCREW, VALVE ATTACHING
7045217, 7050200, 7050716, 7060312PC, 7060507, 7060524, 7060528, 7070520, 7080629, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629, 7150629, 7175629, 7200620
57807
57807 SCREW, TRIM COVER TO BOTTOM COWL (3/4")
7045217, 7050200, 7050716, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629, 7150629, 7175629
4541
4541 SCREW, PLUG - MAIN FUEL JET CHANNEL
7090520, 7090524, 7090529, 7115520, 7115528, 7115529, 7135417PD, 7135826, 7140528, 7140629, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175629, 7200412PD, 7200620
36070
36070 SCREW, WATER INTAKE SCREEN TO GEAR HOUSING
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7150629, 7200620, 7250422PD
86885
86885 SCREW, PLATE TO CYLINDER BLOCK (1 1/2")
70404119D, 7090520, 7090524, 7090529, 7115520, 7115529, 71354120D, 7140629, 7150629, 7200412PD, 7250422PD
63474
63474 SCREW, (.500-20 x 6.00)
7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135473KD, 7135826, 7135D73RD, 7135D73UY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7150453ND, 7150453PD,
42813
42813 SCREW
7001804, 7002201DK, 7075524, 71354120D, 7135412AD, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413AD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727, 7B25201GF