818182 SCREW Mariner
7002201DK, 71354120D, 7135412AD
SCREW
Price: query
Rating:
Mariner entire parts catalog list:
- TRANSOM MOUNT POWER STEERING KIT » 818182
- POWER STEERING COMPONENTS(REMOTE) » 818182
- POWER STEERING COMPONENTS » 818182
- TRANSOM MOUNT POWER STEERING KIT » 818182
- POWER STEERING COMPONENTS(REMOTE) » 818182
Information:
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Note: Refer to Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" for information on replacing the filter.
Turn the ignition switch to the "OFF" position.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. Operate the engine at 1000 to 1200 rpm until the engine runs smoothly in order to remove the residual air from the fuel system.
Once the engine runs smoothly, stop the engine. Turn the ignition switch to the OFF position.Note: You may use the hand priming pump for the fuel filter (IF EQUIPPED) instead of starting engine and running the engine. Perform the following procedure when the hand priming pump is used:
Illustration 1 g00474457
(1) Air purge screw (2) Fuel priming pump (IF EQUIPPED)
Open the air purge screw (1) for the fuel filter by three full turns. Do not remove the air purge screw.
While you operate the hand priming pump (2), observe air purge screw (1). When a small drop of fuel appears at the threads of the air purge screw, close and tighten air purge screw (1) .Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
Continue to operate the fuel priming pump (2) until a strong resistance is felt. Listen for an audible click from the fuel manifold. The click will indicate that the valve has opened and the fuel system is pressurized. Lock the fuel priming pump (2) .
Do not crank the engine for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking again.
Crank the engine. If the engine starts but the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.Note: If the engine will not start, further priming is necessary. If the engine starts but the engine continues to misfire or smoke, further priming is necessary.The Engine Has Been Run Out of Fuel
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Turn the ignition switch to the "OFF" position.
Fill the fuel tank(s) with clean diesel fuel.
Illustration 2 g00474457
(1) Air purge screw (2) Fuel priming pump (IF EQUIPPED)
Open air purge screw (1) for the fuel filter by three full turns. Do not remove the air purge screw.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starter motor to cool for 2 minutes.Note: After four or five cranking intervals, most of the air should be purged from the system.
Crank the engine for 30 seconds. Allow the starter motor to cool for 2 minutes.
Repeat Step 5 until the engine starts and runs. If the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.
Observe air purge screw (1). When a small drop of fuel appears at the threads of the air purge screw, close and tighten air purge screw (1) .Note: Failure to tighten all fittings could result in serious fuel leaks.
Clean any residual fuel from the engine components.
Once the engine runs smoothly, stop the engine. Turn the ignition switch to the OFF position.Note: You may use the hand priming pump for the fuel filter (IF EQUIPPED) instead of starting engine and running the engine. Perform the following procedure when the hand priming pump is used:
Illustration 3 g00474457
(1) Air purge screw (2) Fuel priming pump (IF EQUIPPED)
Open air purge screw (1) for the fuel filter by three full turns. Do not remove the air purge screw.
Parts screw Mariner:
28636
28636 SCREW, DISTRIBUTOR ADAPTOR TO STOP BRACKET (3/4")
7002201DK, 70152374D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080629, 7090520, 7090524, 7090529, 7115473JD, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 71354
22486
22486 SCREW, LATCH TO THROTTLE CONTROL LEVER (7/8")
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727
66725
66725 SCREW, (.375-16 x 3.50)
7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135473KD, 7135826, 7135D73RD, 7135D73UY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7150453ND, 7150453PD,
40003 77
40003 77 SCREW, (M10 x 30), MANIFOLD
7002201DK, 7031203GD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7045217, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7050717, 7055207GD, 7055207HB, 7055207TF, 7
40003 10
40003 10 SCREW, (M5 x 40)
7045217, 7090524, 7115520, 71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7175412PD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727, 7250422PD
13627
13627 SCREW, SPARK ADVANCE LEVER - STOP (1-1/4")
7002201DK, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7150413ED, 7150413HD, 7150423JD, 7175413AD, 7175413PD, 7175413YD, 7175423HD, 7200413JD, 7220727
18699
18699 SCREW, (.250-20 x 1.320), COWL (STANDARD)
7002201DK, 71354120D, 7135412AD, 7135417PD, 7150453PD, 7175412PD, 7175413AD, 7175413PD, 7175413YD, 7200412PD
18303
18303 SCREW, (.190-16 x 1.750)
7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7150413ED, 7150413HD, 7150423JD, 7175412PD, 7175413AD, 7175413PD, 7175423HD, 7200412PD, 7200413JD, 7200473FD, 7200473GD, 7200473HD, 7200473J