82521M Mariner BOLT


82521M BOLT Mariner 7002200, 7002207, 7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7010209, 7015327, 7015529, 7025207PW, 7025500, 7026226, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040706, 7040716 BOLT
82521M BOLT Mariner
Rating:
48

Buy BOLT 82521M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

Mariner entire parts catalog list:

7002200 1980,1985,1988,1989
7002207 1977,1979
7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7005227 1977
7008204 1984,1985,1986
7008208 1978
7008226 1986
7010209 1979,1983,1984,1985,1986
7015327 1987
7015529 1979
7025207PW 1989,1990,1991,1992,1993
7025500 1980
7026226 1986,1988
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992
7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207PW 1989,1990,1991,1992,1993
7040706 1986,1990,1992
7040716 1986

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-6357(1)
or
8T-3022(2) Connecting Rod Guide 1
B 235-0612 Lift Bracket 1
C 136-1452 Retaining Ring Pliers As 1
D 318-4874 Ring Expander Gp 1
E 443-4072 (3)
or
443-4073 (4) Cover 1
G 1U-8692 Piston Pin Guide 1
H 4C-9043 Piston Ring Compressor Gp 1
J 8T-5096
or
369-2607 Dial Indicator 1
K - Bel-Ray Molylube: PN. 67700 -
L 384-8910 Hydraulic Wrench
(1) Use with V-engines
(2) Use with in-line engines
(3) For 6 and 8 cylinders
(4) For 12 and 16 cylinders
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03374611Note: Ensure that there is no damage to the shank of connecting rod bolt (3) prior to the installation of heat shrink tube (10).Note: Ensure that the shanks of connecting rod bolts (3) are free of debris and oil prior to installation.
If a new heat-shrink tube will be installed, follow Step 1.a through Step 1.d.
Clean the shank of connecting rod bolt (3) free of debris and oil.
Slide the new heat shrink tube (10) onto connecting rod bolt (3). Install the new heat shrink tube (10) to Dimension (Y). Dimension (Y) is 1.50 mm (0.059 inch).
Use a suitable heat gun or use a suitable oven to shrink the heat shrink tube (10) onto connecting rod bolt (3). If a suitable oven is used, heat the connecting rod bolt (3) and heat shrink tube (10) at a temperature of 135° 14° C (275° 57°F) for 10 minutes.
After installing the new heat shrink tube (10) onto connecting rod bolt (3), allow connecting rod bolt (3) to cool. Ensure that heat-shrink tube (10) does not have any bumps or wrinkles. Ensure the heat-shrink tube (10) does not move under light finger pressure.
Illustration 2 g03376355Note: Ensure that piston (4) is clean and meets reuse guidelines.
Before the piston rings are installed on the piston, check the end gap on each piston ring. Refer to Specifications, "Piston and Rings".
Do not install the piston rings without the use of the piston ring expander. Piston ring breakage and piston damage may result if the piston ring expander is not used.
Use Tooling (D) to install the piston rings on piston (4).
The piston ring gaps should be separated by 120 degrees. Install the piston rings in the following manner:
Install the piston ring expander on the piston. The ends of the oil ring spring should be installed 180 degrees from the oil ring end gap. The white portion of the oil ring spring must be visible at the ring end gap.
The third piston ring must be installed with Mark "UP-3" upward.
The second piston ring must be installed with Mark "UP-2" upward.
The top ring must be installed with Mark "UP-1" upward.
After the piston rings have been installed, measure the side clearance between the piston rings and the piston grooves. Refer to Specifications, "Piston and Rings".
Locate Mark (4a) on the top of piston (4). Draw an alignment mark on the side of the piston.Note: Mark (4a) is a mill dot on the top of piston (4).
Illustration 3 g03374939
Attach a suitable lifting device to connecting rod (7). The weight of connecting rod (7) is approximately 59 kg (130 lb). Install the upper half of connecting rod bearing (8) in connecting rod (7). Ensure the tabs of the upper half of connecting rod bearing (8) are engaged with the slots in connecting rod (7).
Install Tooling (A) onto the connecting rod bolts. Tooling (A) will hold the upper half of connecting rod bearing (8) in position. Apply clean engine oil to the face of the upper half of connecting rod bearing (8).
Position connecting rod (7) in a VERTICAL position on a suitable surface. Hold the connecting rod (7) to prevent the connecting rod from falling. Remove the suitable lifting device from connecting rod (7).
Illustration 4 g03374721
Attach Tooling (B) and a suitable lifting device to piston (4). The weight of piston (4) is approximately 40 kg (88 lb). Align Mark (4a) with the tab side of the connect


Parts bolt Mariner:

813477M
 
813477M BOLT
7002200, 7002207, 7005207, 7005227, 7008218EW, 7008425, 7015529, 7030320, 7040706, 7040716, 7055524
84237M
 
84237M BOLT
7002200, 7004201, 7005201, 7005207, 7008208, 7008238, 7008248, 7008305, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040328, 7040507, 704
92534M
 
92534M BOLT
7002200, 7003207, 7005207, 7005227
95473M
 
95473M BOLT
7004201, 7005201, 7005207
82447M
 
82447M BOLT, SHIFT HANDLE SHAFT ATTACHING..
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
84239M
 
84239M BOLT
7025200, 7025207NW, 7025500, 7028207, 7028527, 7040507
84342M
 
84342M BOLT
7010209, 7015529, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716, 7055524, 7060507, 7060522, 7060528
41893M
 
41893M BOLT W/WASHER
7020201, 7025200, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7F75413TD
Back to top