82532M Mariner SCREW


82532M SCREW Mariner 7003207, 7005207, 7005227, 7048227, 7048321, 7055324, 7055524, 7060522, 7115F13UF, 7F75413TD SCREW
82532M SCREW Mariner
Rating:
38

Buy SCREW 82532M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mariner entire parts catalog list:

7003207 1987
7005207 1977
7005227 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060522 1982
7115F13UF 2006
7F75413TD 2005,2006

Information:

Start By:a. remove pistons and connecting rods1. Drain the coolant from the cylinder block.2. Put covers on the journals of the crankshaft for protection from dirt or water. 3. Remove cylinder liners (1) with tooling (A).4. Remove the O-ring seals and filler band from each of the cylinder liners. The following steps are for the installation of the cylinder liners. 5. Clean cylinder liners (1) and the liner bores in the cylinder block.6. Install the cylinder liners in the block without the O-ring seals or filler bands.7. Check the cylinder liner projection as follows:a. Install the S1589 Bolts (3) and 1S379 Washers of tooling (B) on the cylinder block next to each liner. Tighten the bolts evenly, in four steps: 14 N m (10 lb.ft.), 35 N m (25 lb.ft.), 70 N m (52 lb.ft.) and 95 N m (70 lb.ft.).b. Put the adapter plate on top of the liner, and install the remainder of tooling (B). Tighten the 1D4595 Bolts (2) evenly in four steps: 7 N m (5 lb.ft.), 20 N m (15 lb.ft.), 35 N m (25 lb.ft.) and 70 N m (52 lb.ft.).c. Check to be sure the distance from the bottom edge of the crossbar to the top of the cylinder block is the same on both sides of the liner.d. Check the cylinder liner projection with tool group (C) at four locations around the liner.e. Liner projection must be 0.033 to 0.175 mm (.0013 to .0069 in.). Measurements on the same liner must not be different by more than 0.05 mm (.002 in.). Average measurements between liners next to each other must not be different by more than 0.05 mm (.002 in.). The maximum permissible difference between average projection of all cylinder liners is 0.10 mm (.004 in.). If the liner is turned in the bore, it can make a difference in the liner projection.8. If the liner projection is not 0.033 to 0.175 mm (.0013 to .0069 in.), check the thickness of the following parts: spacer plate, spacer plate gasket and cylinder liner flange. The thickness of the spacer plate must be 9.970 0.025 mm (.3925 .0010 in.). The thickness of the spacer plate gasket must be 0.208 0.025 mm (.0082 .0010 in.). The thickness of the cylinder liner flange must be 10.282 0.020 mm (.4048 .0008 in.). If the liner projection changes from point to point around the liner, turn the liner to a new position in the bore. If the liner projection is still not to specifications, move the liner to a different bore.9. When the cylinder projection is correct, put an alignment mark on the liner and block so the liner can be installed in the same position from which it was removed. Cylinder liner projection can be adjusted by the removal of material from (machining) the contact face of the cylinder block with the use of the 8S3140 Cylinder Block Counterboring Tool Arrangement. Machine to a minimum depth of 0.76 mm (.030 in.) and to a maximum depth of 1.14 mm (.045 in.). The instructions for the use of the tool group are in Special Instruction, Form No. FM055228. Shims are available for the adjustment of the liner projection. See Cylinder Liner Projection in Testing And Adjusting for the shim thickness and part number.10. Remove tooling (B) and (C). Remove the liner. 11. Put liquid soap on the bottom of the liner bore in the block, on the grooves in lower liner and on O-ring seals (4). Install the O-ring seals on the liner.12. Put filler band (5) in clean SAE 30 oil for a moment, and install it on the liner. Install the cylinder liner immediately in the cylinder block (before expansion of filler band). 13. Make sure the mark on the liner is in alignment with the mark on the block. Use tooling (D) to push the liner into position.14. Do Steps 9 through 13 for the remainder of the cylinder liners.End By:a. install pistons and connecting rods


Parts screw Mariner:

91691M
 
91691M SCREW, W/WASHER
7004201, 7005201, 7005207, 7008218EW, 7008425, 7010209, 7015529, 7020201, 7025200, 7025500, 7026226, 7048321, 7055324, 7060522
81755M
 
81755M SCREW
7003207, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
20411
 
20411 SCREW
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 70402
41889M
 
41889M SCREW
7008218EW, 7008425, 7015327, 7020201, 7025200, 7025207PW, 7025208CW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207PW, 7040208PW, 7040706, 7040716, 7055324, 7055524, 7F10203HD, 7F13203UB, 7F15201GD, 7F25201GD
81281M
 
81281M SCREW, IDLE SPEED
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82484M
 
82484M SCREW, INLET ATTACHING
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82495M
 
82495M SCREW
7048207, 7048227
82524M
 
82524M SCREW
7003207
Back to top