82791M Mariner SCREW


82791M SCREW Mariner 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7015207, 7015307, 7015327, 7025207NW, 7025207PW, 7025208CW SCREW
82791M SCREW Mariner
Rating:
58

Buy SCREW 82791M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mariner entire parts catalog list:

7005207 1977
7005227 1977
7008208 1978
7008218EW 1996,1998
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997
7015207 1977
7015307 1977
7015327 1987
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025208CW 1994,1995,1996,1997,1998

Information:


Illustration 1 g00598786
SchematicTest Step 1. Check for Connector Damage
Verify that the circuit breakers are not tripped.
Turn the circuit breaker for the battery to the OFF position.
Turn the ECS to the OFF/RESET position.
Check connectors and wiring for the following problems: damage, corrosion, abrasion and incorrect attachment.Expected Result:The connectors and wiring should be free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - Proceed to test step 2.
Not OK - Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring. Stop.Test Step 2. Check the Air Shutoff System.
Turn the circuit breaker for the battery to the ON position.
Turn the ECS to the STOP position.
Connect the ET.
Access the override on the ET. Activate the override for the air shutoff.
Disable the override for the air shutoff.Expected Result:The air shutoff relay should activate. The air shutoff relay should deactivate after two seconds. While the relay is active, the air shutoff solenoid should also be active.Results:
OK - The system is operating properly at this time. Stop.
Relays ON - The relay activated but the air shutoff solenoid did not activate. Proceed to test step 3.
Not OK - Both the relay and the solenoid failed to activate. Proceed to test step 4.Test Step 3. Check the Relay.
Turn the circuit breaker for the battery to the OFF position.
Turn the ECS to the OFF/RESET position.
Disconnect the wire from terminal 85 and from terminal 86 of the air shutoff relay.
Obtain two suitable pieces of 18 AWG wire. Connect one end of the first wire to -Battery. Connect the other end to terminal 85 of the air shutoff relay.
Connect one end of the second wire to +Battery. Connect the other end to terminal 86 of the air shutoff relay for two seconds.Expected Result:The air shutoff solenoid should activate when the wire is connected to +Battery.Results:
OK - The relay is operating correctly. The problem is most likely in the wiring.Repair: Repair the connectors and/or wiring or replace the connectors and/or wiring. Stop.
Not OK - The air shutoff relay did not activate. The problem appears to be in the air shutoff relay.Repair: Temporarily install a new air shutoff relay. Ensure that the problem is no longer present. Reinstall the old relay. If the problem returns, replace the air shutoff relay. Stop.Test Step 4. Install a Jumper Wire.
Turn the ECS to the OFF/RESET position.
Disconnect P1 from the ECM. Remove the wire from P1-28.
Install a wire at P1-28. Reconnect ECM connector P1.
Connect the red probe of the multimeter to -Battery. Connect the black probe of the multimeter to the socket of the wire at P1-28.
Turn the circuit breaker for the battery to the ON position.
Turn the ECS to the STOP position.
Access the override on the ET. Activate the override for the air shutoff.This test will cause a 446-05 CID-FMI to be logged. Be sure to delete this CID-FMI when this test is completed.
Disable the override for the air shutoff.
Turn the ECS to the OFF/RESET position. Remove the jumper wire.Expected Result:The voltage should be 24 5 VDC.Results:
OK - The voltage is correct. The problem is not with the ECM. Proceed to test step 5.
Not OK - The voltage is not correct.Repair: Replace the ECM. Refer to Troubleshooting, "Replacing the ECM". Stop.Test Step 5. Test the Relay.
Turn the circuit breaker for the battery to the OFF position.
Turn the ECS to the OFF/RESET position.
Disconnect the relay.
Obtain a suitable piece of 18 AWG wire. Connect one end of the wire to -Battery. Connect the other end of the wire to terminal 85 of the air shutoff relay.
Turn the circuit breaker for the battery to the ON position.
Turn the ECS to the STOP position.
Access the override on the ET. Activate the override for the air shutoff.
Disable the override for the air shutoff.
Remove the jumper wire.Expected Result:The air shutoff relay should activate. The air shutoff relay should deactivate after two seconds. While the relay is active, the air shutoff solenoid should also be active.Results:
OK - The relay and the solenoid are operating properly.Repair: Temporarily install a new air shutoff relay. Ensure that the problem is no longer present. Reinstall the old relay. If the problem returns, replace the air shutoff relay. Stop.
Not OK - Both the relay and the solenoid failed to activate. Proceed to test step 3.Test Step 6. Check the Air Shutoff Solenoid.
Turn the ECS to the OFF position.
Disconnect the negative wire from the air shutoff solenoid. Disconnect the positive wire from the air shutoff solenoid.
Obtain two suitable pieces for 10 AWG wire.
Connect one end of the first wire to the negative terminal of the air shutoff solenoid. Connect the other end to -Battery.
Connect one end of the second wire to +Battery. Connect the other end to the positive terminal of the air shutoff solenoid for one second.Expected Result:When the wire is connected to the positive terminal, the solenoid should activate.Results:
OK - The air shutoff solenoid activated. The problem appears to be in the system wiring.Repair: Check the air shutoff solenoid. The first suspect location is between -Battery and the negative terminal of the air shutoff solenoid. The second suspect location is between the positive terminal of the air shutoff solenoid and terminal 87 of the air shutoff relay. The third suspect location is between terminal 30 of the air shutoff relay and +Battery. Stop.
Not OK - The air shutoff solenoid did not activate. The problem appears to be in the air shutoff solenoid.Repair: Temporarily install a new air shutoff solenoid. Ensure that the problem is no longer present. Reinstall the old solenoid. If the problem returns, replace the air shutoff solenoid. Stop.


Parts screw Mariner:

91691M
 
91691M SCREW, W/WASHER
7004201, 7005201, 7005207, 7008218EW, 7008425, 7010209, 7015529, 7020201, 7025200, 7025500, 7026226, 7048321, 7055324, 7060522
81755M
 
81755M SCREW
7003207, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425
20411
 
20411 SCREW
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7040202, 70402
82164M
 
82164M SCREW, PLATE ATTACHING...
7008238, 7008247, 7048207, 7048227, 7060507, 7060528
81721M
 
81721M SCREW, FRICTION PLATE ADJUSTING
7015207, 7015307, 7015327
82167M
 
82167M SCREW, THROTTLE CAM ATTACHING
7015207, 7020201, 7025200, 7025500, 7028207, 7028527, 7030200
80091M
 
80091M SCREW
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425, 7010209, 7015529, 7028527, 7030200, 7030205, 7030320
811248M
SCREW
811248M SCREW
7008218EW, 7008425, 7025208CW, 7F10203HD, 7F13203UB, 7F15201GD
Back to top