898101015 SCREW Mariner
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK
SCREW
Price: query
Rating:
Mariner entire parts catalog list:
- POWER TRIM-TILT COMPONENTS » 898101015
- POWER TRIM-TILT COMPONENTS » 898101015
- POWER TRIM-TILT COMPONENTS » 898101015
- POWER TRIM-TILT COMPONENTS » 898101015
Information:
1. Remove bolts (1) that hold the elbow in position on the oil pump. Remove the lock and bolt (2) that holds the suction bell to the oil pan plate. 2. Bend the locks back and remove four bolts (3). Remove oil pump (4).
The oil pump idler gear will fall off the pump.
Install Oil Pump
1. Install the idler gear on the oil pump. Put the oil pump in position on the cylinder block and install locks and bolts (1). Be sure the idler gear is engaged with the crankshaft gear before bolts (1) are tightened. 2. Install bolts (3) that hold the elbow to the pump.3. Install the lock and bolt (2) that holds the suction bell to the oil pan plate.end by:a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43.4 6.8 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by: a) install oil pump
The oil pump idler gear will fall off the pump.
Install Oil Pump
1. Install the idler gear on the oil pump. Put the oil pump in position on the cylinder block and install locks and bolts (1). Be sure the idler gear is engaged with the crankshaft gear before bolts (1) are tightened. 2. Install bolts (3) that hold the elbow to the pump.3. Install the lock and bolt (2) that holds the suction bell to the oil pan plate.end by:a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43.4 6.8 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
The oil pump must turn freely by hand after it is assembled.
end by: a) install oil pump
Parts screw Mariner:
824832 4
824832 4 SCREW
7002201UB, 7004201UB, 70152374D, 7020201HB, 7020201TB, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7040203UL, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412U
878388
878388 SCREW, Stainless Steel
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F042016B, 7F04201JB, 7F08201TB, 7F15311ZK
855544013
898101230
898101230 SCREW, Stainless Steel (M4 x 16)
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
898101241
898101241 SCREW, Stainless Steel (M4 x 25)
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
898101018
898101012
898101164