92679M SCREW Mariner
7040206, 7048227, 7048321, 7055324, 7055524, 7060522
SCREW
Price: query
Rating:
Mariner entire parts catalog list:
7048227 1977
- DRIVESHAFT HOUSING » 92679M
- DRIVESHAFT HOUSING » 92679M
- CLAMP AND SWIVEL BRACKET » 92679M
- DRIVESHAFT HOUSING » 92679M
- CLAMP AND SWIVEL BRACKET » 92679M
- DRIVESHAFT HOUSING » 92679M
- CLAMP AND SWIVEL BRACKET » 92679M
- CLAMP AND SWIVEL BRACKET » 92679M
Information:
Introduction
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Method to demonstrate Marine Alarm and Protection System to customers and Marine Certification Society surveyors using the validation Test Kit.Caterpillar recommends that the tests are performed while the engine runs at a low idle as most alarm and shutdown set points are only active while the engine is running. See the appropriate Operation and Maintenance Guide for default set points, alarm set points, and shutdown set points.This document only applies to marine engines equipped with thermowells and isolation valves.Reference Section
Reference: Tool Operating Manual, NEHS1199, Using the 453-3204 Pressure and Temperature Test GroupReference: Caterpillar Channel 1 to show how to use this tool with Wimborne Marine Classification Society (MCS) controls.
Go to https://channel1.videonitch.com.
Sign in.
Search "Alarm, Protection System Testing, & Adjusting".
Click the "Alarm, Protection System Testing, & Adjusting" title.Required Tools
The 453-3204 Tool Gp (Pressure and Temperature Test Group) generates pressures up to 3447 kPa (500 psi) and temperatures from ambient to 350° C (662° F).The tool group contains the following:
Thermo well unit (requires external power)
Pressure hand pump (battery powered)
Connection hose
Adaptor fittings: 12 mm JIC Male, 14 mm JIC Male, 9/16 JIC Male, 7/16 JIC Male, 7/16 JIC Female, and 16 mm sample port
Some tools for sensor removal
O-rings for sensor replacementSensor Testing
Pressure Test Procedure
Setup
While the engine is off, remove the desired pressure sensor from the engine, leaving its respective check valve in place to prevent fluid from leaking.
Connect the test kit hose to the pressure sensor.
Thread the correct adaptor fitting onto the sensor. Turn the adaptor until the seal is covered and the adaptor is firmly seated.Note: To change the units displayed, enter Menu mode and select and scroll through UNITS until the desired units are displayed. Further gauge instructions can be found in the gauge manual included in the test kit.Operation and Testing
Note: Caterpillar recommends
Do not perform any procedure in this Special Instruction until you have read the information and you understand the information.Method to demonstrate Marine Alarm and Protection System to customers and Marine Certification Society surveyors using the validation Test Kit.Caterpillar recommends that the tests are performed while the engine runs at a low idle as most alarm and shutdown set points are only active while the engine is running. See the appropriate Operation and Maintenance Guide for default set points, alarm set points, and shutdown set points.This document only applies to marine engines equipped with thermowells and isolation valves.Reference Section
Reference: Tool Operating Manual, NEHS1199, Using the 453-3204 Pressure and Temperature Test GroupReference: Caterpillar Channel 1 to show how to use this tool with Wimborne Marine Classification Society (MCS) controls.
Go to https://channel1.videonitch.com.
Sign in.
Search "Alarm, Protection System Testing, & Adjusting".
Click the "Alarm, Protection System Testing, & Adjusting" title.Required Tools
The 453-3204 Tool Gp (Pressure and Temperature Test Group) generates pressures up to 3447 kPa (500 psi) and temperatures from ambient to 350° C (662° F).The tool group contains the following:
Thermo well unit (requires external power)
Pressure hand pump (battery powered)
Connection hose
Adaptor fittings: 12 mm JIC Male, 14 mm JIC Male, 9/16 JIC Male, 7/16 JIC Male, 7/16 JIC Female, and 16 mm sample port
Some tools for sensor removal
O-rings for sensor replacementSensor Testing
Pressure Test Procedure
Setup
While the engine is off, remove the desired pressure sensor from the engine, leaving its respective check valve in place to prevent fluid from leaking.
Connect the test kit hose to the pressure sensor.
Thread the correct adaptor fitting onto the sensor. Turn the adaptor until the seal is covered and the adaptor is firmly seated.Note: To change the units displayed, enter Menu mode and select and scroll through UNITS until the desired units are displayed. Further gauge instructions can be found in the gauge manual included in the test kit.Operation and Testing
Note: Caterpillar recommends
Parts screw Mariner:
82514M
82511M
82511M SCREW, RETAINER ATTACHING
7008218EW, 7008425, 7015207, 7015307, 7015327, 7028207, 7028527, 7040207, 7040507, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
82523M
81292M
81292M SCREW, PLUG
7040207, 7040208, 7040328, 7040507, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83481M
81279M
82981M
97832M