19368 2 SEAL, (4.20 Inch), Black, Gray Mariner
7075312ND, 7075312SD, 7100412NC
SEAL
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$476.88
26-07-2024
13.0[5.85] pounds
US: Rareelectrical
RAREELECTRICAL New Pto Clutch Compatible With Toro Lawn Mowers Xl440h 2005-2010 Timcutters 1089512 521956
Rareelectrical Rareelectrical Brand Compatible with TORO || Replaces: REPLACES: 108-9512 5219-56 1089512 521956, ITEM DESCRIPTION: PTO CLUTCH, CRANKSHAFT DIAMETER: 1.125", PULLEY DIAMETER: 7", ROTATION: COUNTERCLOCKWISE, FT LBS TORQUE: 125, WEIGHT: 12 LBS. ... || Full One Year Warranty || Computer tested for consistent Quality and unsurpassed reliability || PTO Clutch - Rotation: Counterclockwise Crankshaft Diameter: 1.125" FT LBs Torque: 125 Pulley Diameter: 7" Source: Aftermarket
Rareelectrical Rareelectrical Brand Compatible with TORO || Replaces: REPLACES: 108-9512 5219-56 1089512 521956, ITEM DESCRIPTION: PTO CLUTCH, CRANKSHAFT DIAMETER: 1.125", PULLEY DIAMETER: 7", ROTATION: COUNTERCLOCKWISE, FT LBS TORQUE: 125, WEIGHT: 12 LBS. ... || Full One Year Warranty || Computer tested for consistent Quality and unsurpassed reliability || PTO Clutch - Rotation: Counterclockwise Crankshaft Diameter: 1.125" FT LBs Torque: 125 Pulley Diameter: 7" Source: Aftermarket
Mariner entire parts catalog list:
- COWLS AND FRONT COVER » 19368 2
- COWLS AND FRONT COVER » 19368 2
- COWLS AND FRONT COVER » 19368 2
- COWLS AND FRONT COVER » 19368 2
- COWLS AND FRONT COVER » 19368 2
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 388-1289 Capping Kit 1 Start By:
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Note: Place identification marks on all hoses, on all hose assemblies, on wires and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies will prevent fluid loss. Plugging all hose assemblies and tube assemblies will to keep contaminants from entering the system.Note: Plug or cap all open ports with new plugs or caps.
Illustration 1 g02701543
Illustration 2 g02701718
Disconnect wiring harness assembly (5) from electronic unit injector (3). Note: Make a temporary mark on the wiring harness assembly in order to ensure that the wiring harness assembly is connected to the correct electronic unit injector during assembly.
Remove clip (1) from electronic unit injector (3).
Disconnect hose assembly (2) from electronic unit injector (3). Remove O-ring seal (7) from the hose assembly.
Use Tooling (A) in order to cap electronic unit injector (3) immediately. Use Tooling (A) in order to plug hose assembly (2) immediately.
Remove nut (4) and washer (8) from clamp (6). Note: Note the orientation of the washer.
Make a temporary mark on the electronic unit injector in order to ensure that the electronic unit injector is reinstalled in the original location.
Remove the electronic unit injector and clamp (6) from the cylinder head. Note: Always handle electronic unit injectors with care.
Remove clamp (6) from electronic unit injector (3).
If electronic unit injector (3) is to be reused, Follow Step 10 through Step 11 in order to remove sealing washer (10).
Use a suitable tool in order to remove sealing washer (10) from electronic unit injector (3). If sealing washer (10) is not present on the electronic unit injector, ensure that the sealing washer is removed from the cylinder head. Note: Ensure that the nozzle for the electronic unit injector is not damaged in any way during removal of the sealing washer.
Install Tooling (A) to the nozzle for electronic unit injector (3) immediately.
If necessary, repeat Step 1 through Step 10 in order to remove the remaining electronic unit injectors. In some applications removal of the clean emissions bracket and exhaust gas recirculation valve will be necessary in order to remove number four electronic unit injector. Refer to Disassembly and Assembly, "Support and Mounting (CEM) - Remove and Install" and Disassembly and Assembly, "Exhaust Gas Recirculation Valve - Remove and Install" for the correct procedures.
If necessary, remove studs (9) from the cylinder head.
Parts seal Mariner:
38970
38970 SEAL, RUBBER - WATER INLET TUBE ( DRIVE SHAFT HSG. PLATE)
7002201DK, 7050412YD, 7060412ET, 7075524, 7080508, 7080629, 7085507, 7090520, 7090524, 7090529, 7100412NC, 7115412TB, 7115473JD, 7115520, 7115528, 7115529, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 713547
67260
67260 SEAL
7075312ND, 7075312SD, 7075717, 7100412NC, 7135826, 7150453ND, 7150629, 7175629, 7200620, 7220727
41953
41953 SEAL
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7045217, 7050200, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7050716, 705
87735
87735 SEAL, Oil
7002201DK, 7045217, 7050717, 7060312PC, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075524, 7075717, 7075D73UY, 7075D73ZY, 7090412TB, 7090412TD, 70904
18306 1
42935
42940 4
19386 1