38452 Mariner SEAL, RUBBER - WATER INLET TUBE (WATER PUMP BODY)


38452 SEAL, RUBBER - WATER INLET TUBE (WATER PUMP BODY) Mariner 70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520 SEAL
38452 SEAL, RUBBER - WATER INLET TUBE (WATER PUMP BODY) Mariner
Rating:
48

Buy SEAL, RUBBER - WATER INLET TUBE (WATER PUMP BODY) 38452 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

Mariner entire parts catalog list:

Information:

Travel Speed
The "TRAVEL SPEED" key is used to select one of the following two travel speeds:
HIGH
LOWWhen the "HIGH" travel speed is selected, the controller will activate the travel speed solenoid. This activation will cause the travel speed to increase according to the travel load. Selecting the "LOW" travel speed will deactivate the travel speed solenoid. This action will cause the travel speed to decrease.The travel speed solenoid is energized and the rabbit indicator illuminates under the following conditions:
The output pressure of the pump is less than or equal to 20600 kPa (2988 psi) for 0.4 seconds or more. This energizes the travel speed solenoid in order to keep the travel speed HIGH.The travel speed solenoid is not energized but the rabbit indicator illuminates under the following conditions:
The output pressure of the pump is greater than 20600 kPa (2988 psi) for 0.4 seconds or more.This does not energize the travel speed solenoid in order to keep the travel speed LOW.For more information, see the following topics:
Hydraulic System Systems Operation, "Trenching Operation"
Hydraulic System Systems Operation, "Leveling Operation"
Hydraulic System Systems Operation, "Pilot Circuit"
Hydraulic System Systems Operation, "Travel Control"Backup System
Illustration 1 g00662823
(1) Backup switch (2) Speed change switchThe controller has a backup system in order to prevent uncontrolled operation of the pump and/or engine. When the backup switch (1) is placed in the manual position, the following conditions result:
The proportional reducing valve is disconnected from the drive circuit of the proportional reducing valve. Then, the reducing valve is driven by a constant current that is adjusted by the backup resistor. The power shift pressure is kept constant and pump output is in the standard mode.
The monitor does not display any information. The controller and the monitor are not receiving power.
The engine speed can be controlled by the speed change switch (2). The engine speed will be increased, if the speed change switch is placed in the rabbit position. The engine speed will be decreased, if the switch is placed in the tortoise position. The switch returns to the neutral position when the switch is released.
The swing parking brake is released. However, the parking brake is engaged when the primary pilot pressure is reduced to near zero by placing the


Parts seal Mariner:

6204
 
6204 SEAL, THROTTLE SHAFT
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7075524, 7080508, 7080629, 7085507
71090
 
71090 SEAL, CARBURETOR PLATE
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
62444
 
62444 SEAL, RUBBER-TOP BRACKET AND COVER MOUNTING PLATE
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
69876 1
 
69876 1 SEAL, REAR BRACKET AND TOP BRACKET
7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
76410
 
76410 SEAL, FUEL CONNECTOR-SOUND ATTENUATOR
7050716, 7060312PC, 7060524, 7070509, 7070520
41953
 
41953 SEAL
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7045217, 7050200, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7050716, 705
38133
96401
 
96401 SEAL, UPPER MOUNT
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070520
Back to top