66302 Mariner SEAL, Oil


66302 SEAL, Oil Mariner 7200413JD, 7200473FD, 7200473GD, 7200473HD, 7200473JD, 7200473KD, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412CD, 7225412HD, 7225413DD, 7225413HD, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7B25201GF SEAL
66302 SEAL, Oil Mariner
Rating:
78

Buy SEAL, Oil 66302 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 35
 

Mariner entire parts catalog list:

7200413JD 2000
7200473FD 1997
7200473GD 1998
7200473HD 1999
7200473JD 2000
7200473KD 2001,2002
7200D73MD 2003
7200D73RD 2004,2005,2006
7200D73ZY 2006
7225412CD 1994,1995,1996,1997,1998
7225412HD 1999,2000,2001
7225413DD 1995,1996,1997,1998
7225413HD 1999,2000,2001
7225413LD 2002,2003
7225413RD 2004,2005,2006
7225413ZY 2006
7225E73MD 2003,2004
7B25201GF 1998

Information:


Illustration 1 g00813712
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector and all other connectors in the circuit. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points. All connections and grounds should be tight and free of corrosion.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check the Resistance through the Solenoid
Disconnect the J508/P508 fan control solenoid connector.
Measure the resistance of the sensor between J508:1 (Fan Control Solenoid) and J508:2 (Solenoid Return).Expected Result:Resistance should be between 4.5 and 5.5 Ohms.Results:
OK - Proceed to Test Step 4.
Not OK - There may be a problem with the fan control solenoid. Proceed to Test Step 3.Test Step 3. Temporarily Install a New Fan Control Solenoid
Remove the fan control solenoid.
Temporarily install a new fan control solenoid.
Start the engine. Ensure that the keyswitch is in the ON position.
Compare the status for "Fan Pump Pressure" to the status for "Desired Fan Pump Pressure" on ET.
Turn the keyswitch to the OFF/RESET position.Expected Result:The status for "Fan Pump Pressure" should closely correlate with the status for "Desired Fan Pump Pressure".Results:
OK - The fan control solenoid was faulty.Repair: Permanently install the new fan control solenoid.Verify that the repair eliminates the problem.STOP
Not OK - There may be a problem with the harness. Proceed to Test Step 4.Test Step 4. Check for Shorts in the Harness
Illustration 2 g00815132
ECM connector P1
Disconnect the J1/P1 ECM connector and the J508/P508 fan control solenoid connector.
Measure the resistance between P1:43 (Fan Control Solenoid) and chassis ground.
Measure the resistance between P1:51 (Solenoid Return) and chassis ground.
Measure the resistance between P1:43 (Fan Control Solenoid) and P1:51 (Solenoid Return).Expected Result:The resistance for each measurement should be greater than 20,000 Ohms.Results:
OK - Proceed to Test Step 5.
Not OK - There is a short between the ECM and the fan control solenoid.Repair: Repair the circuit.STOPTest Step 5. Check for Open Circuits in the Harness
Illustration 3 g00815132
ECM connector P1
Ensure that the keyswitch is in the OFF/RESET position and that the J1/P1 ECM connector is disconnected.
Use a suitable piece of wire to short P1:43 (Fan Control Solenoid) and P1:51 (Solenoid Return).
Disconnect the J508/P508 fan ontrol solenoid connector.
Measure the resistance between P508:1 (Fan Control Solenoid) and P508:2 (Solenoid Return).Expected Result:The resistance should be less than 10 Ohms.Results:
OK - Proceed to Test Step 6.
Not OK - There is an open circuit in the wiring harness between the fan control solenoid and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 6. Compare "Fan Pump Pressure" to "Desired Fan Pump Pressure"
Start the engine.
Compare the status for "Fan Pump Pressure" to the status for "Desired Fan Pump Pressure" on ET.
Turn the keyswitch to the OFF/RESET position.Expected Result:The status for "Fan Pump Pressure" should closely correlate with the status for "Desired Fan Pump Pressure".Results:
OK - The system is functioning correctly.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - Proceed to Test Step 7.Test Step 7. Measure the Current to the Fan Control Solenoid
Reconnect the J1/P1 ECM connector.
The J508/P508 fan control solenoid connector should still be disconnected. Install a jumper wire between J508:2 and P508:2.
Connect an ammeter that is capable of withstanding a 5 Amp current between J508:1 and P508:1.
Start the engine and observe the reading on the ammeter that is installed in the circuit.
Turn the keyswitch to the OFF/RESET position.
Remove the ammeter and the jumper wire from the circuit.
Reconnect the J508/P508 fan control solenoid connector.Expected Result:The ECM should be supplying between 0.65 and 1.8 Amp to the fan control solenoid.Results:
OK - The ECM appears to be supplying the correct current to the solenoid. Either the pump or the motor may not be responding correctly.Repair: Troubleshoot the hydraulic system. Refer to Testing and Adjusting, "Hydraulic and Steering System".STOP
Not OK - The ECM may not be producing a valid supply.Repair: Verify your results.Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM.Verify that the repair eliminates the problem.STOP


Parts seal Mariner:

825318 1
 
825318 1 SEAL, Cowl (41.00 Inches)
7075D73UY, 7090D73RD, 7115473JD, 7115F13KD, 7115F13RD, 7115F13UF, 7135412ED, 7135412HD, 7135412JD, 7135473GD, 7135473HD, 7135473KD, 7135D73RD, 7135D73UY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7175423HD, 7200413J
818574
SEAL
818574 SEAL
7200413JD, 7200473FD, 7200473GD, 7200473HD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412CD, 7225412HD, 7225413DD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
18792 1
SEAL
18792 1 SEAL
7200413JD, 7225413DD, 7225413HD
859093
SEAL
859093 SEAL
7200413JD, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225412HD, 7225413HD, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
878453
SEAL
878453 SEAL
7200473KD, 7225412HD, 7225413LD
882767
SEAL
882767 SEAL
7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7250423IY
884391
SEAL
884391 SEAL
7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225413IY, 7225413LD, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
832940001
SEAL
832940001 SEAL
7200D73IY, 7200D73RD, 7200D73ZY, 7225413IY, 7225413RD, 7225413ZY, 7225E73MD, 7250423IY
Back to top