84033M Mariner SEAL SEE NOTE #12


84033M SEAL SEE NOTE #12 Mariner 7010209, 7015529 SEAL
84033M SEAL SEE NOTE #12 Mariner
Rating:
73

Buy SEAL SEE NOTE #12 84033M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 69
 

Compatible models:

7010209   7015529   Mariner

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 8T-5096 Tool Gp 1
C - Bel-Ray Molylube 67700(1) -
(1) Refer to the following link to order molylube specified above - www.belray.com.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00577390
If crankshaft gears (6) were removed, install crankshaft gears (6) on the crankshaft and install bolts (7).
Check the clearance of the bearings. Refer to Disassembly and Assembly, "Bearing Clearance - Check" for the correct procedure.
Illustration 2 g01353563Note: Place clean engine oil on the main bearings and on the connecting rod bearings prior to installation.Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies.
Illustration 3 g01353615
Typical example
Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach a suitable lifting device to crankshaft (4) and position the crankshaft in the cylinder block. The weight of crankshaft (4) is approximately 762 kg (1680 lb).
Illustration 4 g01353620
Tightening sequence
Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Place Tooling (C) on the bolts for the main bearing caps.
Illustration 5 g01353682
Place clean engine oil on thrust plates (3). Install thrust plates (3) on each side of the center main bearing.
Place main bearing caps (5) into position and install the bolts. Tighten the bolts in the numerical sequence that is shown above to a torque of 190 14 N m (140 10 lb ft). Tighten the bolts again for an additional 180 5 degrees.
Check the end play with Tooling (B). The end play must not exceed 0.40 0.23 mm (0.0157 0.0091 inch).
Illustration 6 g01353696
Position the connecting rods on the journals of the crankshaft. Install connecting rod bearing caps (2).Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 7 g01353701
Tightening sequence
Place Tooling (C) on the bolts for the connecting rod caps and install the bolts.
Tighten the bolts with the following steps:
Tighten bolts (14) and (15) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (14) and (15) again to a torque of 90 5 N m (65 4 lb ft).
Tighten bolts (16) and (17) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn). An impact wrench may be used.
Place the remaining connecting rod caps in position and tighten the bolts with the same procedure that is in Steps 12a through 12e.
Illustration 8 g01353745
Each counterweight is numbered and must be installed in the same position as the corresponding number on the cranksh


Parts seal Mariner:

94574M
 
94574M SEAL SEE NOTE #11
7010209, 7015529
83982M
83983M
 
83983M SEAL
7010209, 7015529
96595M
 
96595M SEAL
7010209, 7015529
94542M
 
94542M SEAL
7010209, 7015529
84244M
 
84244M SEAL
7010209, 7015529
83987M
 
83987M SEAL
7010209, 7015529
17659M
 
17659M SEAL
7015529
Back to top