13536A 2 Mariner SENSOR ASSEMBLY


13536A 2 SENSOR ASSEMBLY Mariner 7200473FD, 7200473JD, 7225412CD SENSOR
13536A 2 SENSOR ASSEMBLY Mariner
Rating:
13

Buy SENSOR ASSEMBLY 13536A 2 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 48
 

Compatible models:

Mariner entire parts catalog list:

7200473FD 1997
7200473JD 2000
7225412CD 1994,1995,1996,1997,1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Lifting Bracket 1
B - Guide Stud
(M10 x 1.25 by 80 mm) 2 Start By:
Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Remove the primary speed/timing sensor. Refer to Disassembly and Assembly, "Primary Engine Speed/Timing Sensor - Remove and Install" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03795183
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Remove two bolts (1) from Positions (X) on the flywheel.
Install Tooling (B) in Positions (X) on the flywheel.
Remove the remaining bolts (1) and remove flywheel (2).Note: A roll pin (3) is located between the crankshaft and the flywheel.
Inspect ring gear (4) and flywheel (2) for wear or damage. If the ring gear or the flywheel is worn or damaged, use new parts for replacement.
Illustration 2 g03795192
To remove ring gear (4) from flywheel (2), place the flywheel on a suitable support. Use a hammer and a punch (5) to remove the ring gear from the flywheel.Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Lifting Bracket 1
B - Guide Stud
(M10 x 1.25 by 80 mm) 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been heated.
Illustration 3 g03795238
If the ring gear was removed, follow Steps 1.a through 1.c to install ring gear (4) to flywheel (2).
Identify the orientation of the new ring gear to install the ring gear correctly onto the flywheel.Note: The chamfered side of Gear Teeth (Y) must face toward the starting motor when the flywheel is installed. The chamfered will ensure the correct engagement of the starting motor.
Heat ring gear (4) in an oven to a maximum temperature of 150°C (302°F) prior to installation. Note: Do not use a torch to heat the ring gear.
Ensure that ring gear (4) orientation is correct and quickly install the ring gear onto flywheel (2).
Illustration 4 g03795183
Thoroughly clean the flywheel housing. Inspect the crankshaft rear seal for leaks. If crankshaft rear seal has any oil leaks, replace the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove and Install" for the correct procedure.
Install Tooling (B) to Positions (X) in the crankshaft.
Install Tooling (A) and a suitable lifting device to flywheel (2). The weight of the flywheel is approximately 42 kg (93 lb).
Position flywheel (2) onto Tooling (B).Ensure that roll pin (3) is installed to the crankshaft and that the roll pin is free from damage. Align the hole in the flywheel with the roll pin in the crankshaft.
Install bolts (1) finger tight.
Remove Tooling (B) and install the two remaining bolts (1).
Use a suitable tool to prevent flywheel (2) from rotating. Tighten bolts (1) to a torque of 74 N m (54 lb ft).
Remove Tooling (A) and the lifting device from the flywheel.End By:
Install the primary speed/timing sensor. Refer to Disassembly and Assembly, "Primary Engine Speed/Timing Sensor - Remove and Install" for the correct procedure.
Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.


Parts sensor Mariner:

821909
SENSOR
821909 SENSOR
7200413JD, 7225412CD, 7225412HD, 7225413DD, 7225413HD
13536A11
821664
SENSOR, Throttle Position (TPI)
821664 SENSOR, Throttle Position (TPI)
7200413JD, 7225412CD, 7225412HD, 7225413DD, 7225413HD
825762
SENSOR, MAP
825762 SENSOR, MAP
7135473GD, 7135473HD, 7200413JD, 7200473FD, 7200473GD, 7200473HD, 7225413DD, 7225413HD
13536A12
SENSOR ASSEMBLY, Temperature
13536A12 SENSOR ASSEMBLY, Temperature
7115473JD, 7135473GD, 7135473HD, 7135473KD, 7200473GD, 7200473HD, 7200473JD, 7200473KD, 7F25201GD, 7F25203JB
858535
 
858535 SENSOR ASSEMBLY, Temperature
7115473JD, 7135473KD, 7150413LD, 7200473JD, 7200473KD, 7200D73MD, 7225413LD, 7A30302LB, 7A41412LB, 7F25203JB, 7F25203LB, 7F30203HD, 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD
854445
 
854445 SENSOR, MAP
7075D73UY, 7075D73ZY, 7090D73RD, 7115473JD, 7135473KD, 7135D73RD, 7135D73UY, 7135D73ZY, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY, 7200473JD, 7200473KD, 7200D73IY, 7200D73MD, 7200D73RD, 7200D73ZY, 7225413IY, 7225413L
859223
Back to top