83527M Mariner SHAFT, THROTTLE CONTROL


83527M SHAFT, THROTTLE CONTROL Mariner 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040716 SHAFT
83527M SHAFT, THROTTLE CONTROL Mariner
Rating:
78

Buy SHAFT, THROTTLE CONTROL 83527M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Compatible models:

Mariner entire parts catalog list:

7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040208 1978
7040328 1978,1980
7040507 1987
7040716 1986

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1 Start By:
Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The removal procedure is identical the three cylinder and the four cylinder engines. The Illustrations show a four cylinder engine.
Clean the bottom face of the cylinder head. Check the depth of the valves below the face of the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder Head Valves" for the correct dimensions.
Place a temporary identification mark on the heads of the valves in order to identify the correct position. Note: Do not stamp the heads of the valves. Stamping or punching the heads of the valves could cause the valves to fracture.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Illustration 1 g03341245
Illustration 2 g03341246
Use Tooling (A) in order to compress the appropriate valve spring (3). Note: Do not compress the valve spring so that valve spring retainer (2) touches valve stem seal (4).
Remove valve keepers (1).
Remove Tooling (A).
Remove valve spring retainer (2).
Remove valve spring (3).
Remove valve (5).
Remove valve stem seal (4).
Repeat Step 3 though Step 9 to remove the remaining valves. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-3527 Valve Spring Compressor 1
B(1) 256-4865 Valve Stem Seal Replacer 1
(1) C1.5 and C2.2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The installation procedure is identical the three cylinder and the four cylinder engines. The Illustrations show a four cylinder engine.
Clean all components of the cylinder head assembly. Ensure that all ports, all coolant passages, and all lubrication passages in the cylinder head are free from debris. Follow Step 1.a through Step 1.e in order to inspect the components of the cylinder head assembly. Replace any components that are worn or damaged.
Inspect the cylinder head for wear and for damage. Refer to Systems Operation, Testing and Adjusting, "Cylinder Head Inspect" for the correct procedure.
Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for further information.
Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder Head Valves" and Systems Operation, Testing and Adjusting, "Valve Guide - Inspect" for further information.
Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head Valves" for the correct procedure.
Inspect the valve springs for the correct length. Refer to Specifications, "Cylinder Head Valves" for the correct procedure.
Illustration 3 g03341247
Use Tooling (B) to install new valve stem seals (4) onto each of the valve guides. Note: The outer face of the valve guides must be clean and dry before installing the valve stem seals.
Illustration 4 g03341246
Lubricate the stem of valve (5) with clean engine oil. Install valve (5) in the appropriate position in the cylinder head. Check the depth of the valve below the face of the cylinder head. Refer to Systems Operation, Testing and Adjusting, "Valve Depth - Inspect" for more information.
Install valve spring (3) to the cylinder head.
Position valve spring retainer (2) onto valve spring (3). Show/hide t


Parts shaft Mariner:

83590M
 
83590M SHAFT, SHEAVE
7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7030320, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
83464M
 
83464M SHAFT
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83484M
 
83484M SHAFT
7040207, 7040507
6984M
 
6984M SHAFT, CRANK
7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040716
83534M
 
83534M SHAFT
7040207, 7040208, 7040328, 7040507
83428M
 
83428M SHAFT, PROPELLER
7040207, 7040507
83516M
 
83516M SHAFT, STEERING HANDLE
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
83555M
 
83555M SHAFT, LINK CONNECTING
7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
Back to top