822250 Mariner SHIFT SHAFT


822250 SHIFT SHAFT Mariner 7016207CD SHIFT
822250 SHIFT SHAFT Mariner
Rating:
8

Buy SHIFT SHAFT 822250 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$26.89
 

09-01-2022

-: -
Engine Crankshaft Crank & Oil Seal Set fits - Breeze & Grizzly 125 1991-2012 822250 - Wear-Resistant Seal Set - High Strength Rubber Seals
Over 10,000 Options: The replacement parts will fit both OLD and NEW models of lawn mowers, petrol cutters, trimmers, motorcycles, ATVs, cars, and agricultural machinery of most types. Check our STORE to find everything in one place. || Compatible: Breeze & Grizzly 125 1991-2012 || This is NOT an OEM part. || Long Life: Our dependable, reliable replacement parts and repair kits will help keep your engines and power equipment running at their best for years to come. This means you save time and money on repairs and get outstanding performance from your equipment with minimal downtime and productivity loss. || Ultimate Durability and Productivity: The replacement parts are made of extra sturdy rust- and wear-resistant material. Before marketing, all our spare patrs and repair kits are tested to ensure complete compatibility and impeccable operation over extended periods in all kinds of weather conditions. Your power equipment will function optimally throughout years of daily, intensive use.
$14.50
 

26-09-2017
.40[0.00] pounds
QUADBOSS: QUADBOSS
QUADBOSS 822250 QB OIL SEAL SET
QuadBoss Oil Seal Set
$12.96
 

02-10-2017
.90[0.00] pounds
Winderosa: Winderosa
Winderosa Oil Seal Kit 822250
Made from the highest quality materials available||Comes with all seals necessary to rebuild the engine and transmission
Number on catalog scheme: 35
 

Compatible models:

7016207CD   Mariner

Mariner entire parts catalog list:

7016207CD 1994,1995,1996

Information:


Table 2
Required Tooling for the Procedure
373-4609 Spark Tester
Table 3
Troubleshooting Test Steps Values Results
1. Determine the Code
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Use the "Aftertreatment #1 Ignition Transformer Primary Override" on Cat ET to turn on the ARD ignition system. The ARD ignition system must operate for 20 seconds in order for a diagnostic trouble code to become active. securely.
C. Determine the code that is present.
Diagnostic code
Result: A 2465-5, 2465-6, 3484-5 or 3484-6 code is present.
Proceed to Test Step 5.
Result: A 3180-5 or 4265-5 code is present or a diagnostic code is not present.
Proceed to Test Step 2.
2. Inspect the Ignition Wire
A. Visually inspect the ignition wire between the ignition coil and the ARD combustion head. Look for the following problems:
1. Loose connections or damaged connectors
2. Moisture on the connectors or the ignition wire
3. Damage to the ignition wire that is caused by excessive heat
4. Damage to the ignition wire that is caused by chafing
5. Improper routing of the ignition wire
6. Damaged insulation on the ignition wire
B. Push the boot on each end of the ignition wire. This tests whether the clip inside the boot is connected to the spark plug and to the ignition coil. There should be a "click" when you push the boot onto either part. If you felt a "click", the clip inside the boot was not previously connected.
Damaged wire
Result: The ignition wire is not damaged.
Proceed to Test Step 3.
Result: The ignition wire is damaged.
Repair: Replace the ignition wire.
Proceed to Test Step 8.
Illustration 1 g02388518
(1) 373-4609 Spark Tester
Illustration 2 g02309455
Table 4
Troubleshooting Test Steps Values Results
3. Check for Spark at the Coil Output, Using the Spark Indicator
A. Assemble the 373-4609 Spark Tester as shown in Illustration 1.
Ensure that the alligator clip is secured to a good ground source.
B. Install the spark indicator as shown in Illustration 2.
C. Use the "Aftertreatment #1 Ignition Transformer Primary Override" on Cat ET to turn ON the ARD ignition system. Check for spark in the spark indicator.
Spark
Result: Spark is present in the indicator.
Proceed to Test Step 4.
Result: Spark is not present in the indicator.
Repair: Replace the ignition coil. Inspect the connector terminals. If terminal damage/erosion is found, repair the ground from the coil housing to the chassis. Also, inspect the ground wire from the coil to the ARD head.
Proceed to Test Step 8.
Illustration 3 g02478839
Table 5
Troubleshooting Test Steps Values Results
4. Check for Spark to the Spark Plug
A. Assemble the 373-4609 Spark Tester as shown in Illustration 3.
B. Install the spark plug indicator between the spark plug and the end of the spark plug wire.
C. Use the "Aftertreatment #1 Ignition Transformer Primary Override" on Cat ET to turn ON the ARD ignition system. Check for spark in the spark indicator.
Spark
Result: Spark is present in the indicator.
Repair: Replace the spark plug.
Proceed to Test Step 8.
Result: Spark is not present in the indicator.
Repair: Replace the ignition wire.
Proceed to Test Step 8.
Illustration 4 g01395281
Information for the ignition circuit.
Table 6
Troubleshooting Test Steps Values Results
5. Replace the Ignition Wire
A. Replace the ignition wire between the ignition coil and the ARD combustion head.
B. Use the "Aftertreatment #1 Ignition Transformer Primary Override" on Cat ET to turn on the ARD ignition system.
Ignition Wire
Result: The


Parts shift Mariner:

823952 1
 
823952 1 SHIFT HANDLE (USE WITHOUT REF. #4)
70152374D, 7016207CD, 7020201HB, 7020201TB
823601 1
 
823601 1 SHIFT SHAFT (HORIZONTAL)
70152374D, 7016207CD, 7020201HB, 7020201TB
822249
Back to top