18960M Mariner SHIM (0.50MM) SEE NOTE #3


18960M SHIM (0.50MM) SEE NOTE #3 Mariner 7010209, 7015529, 7025500, 7026226, 7030320 SHIM
18960M SHIM (0.50MM) SEE NOTE #3 Mariner
Rating:
78

Buy SHIM (0.50MM) SEE NOTE #3 18960M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 56
 

Compatible models:

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015529 1979
7025500 1980
7026226 1986,1988
7030320 1980,1990,1992

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Drill Bit (3 mm) 1
B 1U-7600 Slide Hammer Puller 1
C 1U-7262 Telescopic Magnet 1 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the correct procedure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02873976
Typical example
Apply clean grease to Tooling (A) in order to prevent any swarf that is generated from entering the engine. Use Tooling (A) to drill three evenly spaced holes in crankshaft rear seal (4).
Use Tooling (B) with care in order to remove crankshaft rear seal (4) from flywheel housing (1). Alternate the position of Tooling (B) from one hole to another. Alternating the position of Tooling (B) will allow the crankshaft rear seal to be easily removed from the flywheel housing.
Apply clean grease to Tooling (A) in order to prevent any swarf that is generated from entering the engine. Use Tooling (A) to drill two evenly spaced holes in crankshaft wear sleeve (3).
Use Tooling (B) with care in order to remove crankshaft wear sleeve (3) from crankshaft (2). Alternate the position of Tooling (B) from one hole to the other. Alternating the position of Tooling (B) will allow the crankshaft wear sleeve to be easily removed from the crankshaft.
Use Tooling (C) to collect any swarf that is on the flywheel housing or crankshaft assembly. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
D 390-1124 Crankshaft Rear Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the flange of the crankshaft and the inside of the flywheel housing are clean and free from oil and damage.
Illustration 2 g02876556
Typical example
Illustration 3 g03789262
Sectional view of the crankshaft rear seal, the crankshaft, and the installation tool
Crankshaft rear seal (4) and crankshaft wear sleeve (3) are supplied as a crankshaft rear seal assembly (5) and should not be separated for installation. Note: Do not remove the crankshaft rear seal from the crankshaft wear sleeve.
Use Tooling (D) and follow Step 3.a through Step 3.f in order to install crankshaft rear seal assembly (5).
Position the adaptor of Tooling (D) onto the palm of the crankshaft and secure with bolts.
Position the new crankshaft rear seal assembly (5) over the adaptor onto the rear of the crankshaft.
Align the seal installer of Tooling (D) with the crankshaft. Note: Check that the installer of Tooling (D) is parallel to the adaptor.
Install the nut and washer to the locator.
Tighten the nut until the installer bottoms out on the adaptor in order to install crankshaft rear seal assembly (5) into flywheel housing (1) and onto crankshaft (2).
Remove Tooling (D). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct procedure.


Parts shim Mariner:

80258M
 
80258M SHIM, REVERSE GEAR (0.1MM)...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529
80259M
 
80259M SHIM, REVERSE GEAR (0.3MM)...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529
80260M
 
80260M SHIM, REVERSE GEAR (0.5MM)...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7010209, 7015207, 7015307, 7015327, 7015529
19120M
 
19120M SHIM, DRIVE SHAFT (0.18MM)
7025500, 7026226, 7030205, 7030320
19121M
 
19121M SHIM, DRIVE SHAFT (0.30MM)
7025500, 7026226, 7030205, 7030320
19122M
 
19122M SHIM, DRIVE SHAFT (0.40MM)
7025500, 7026226, 7030205, 7030320
19125M
 
19125M SHIM, REVERSE GEAR (0.10MM)
7025500, 7026226, 7030205, 7030320
19126M
SHIM, REVERSE GEAR (0.12MM)
19126M SHIM, REVERSE GEAR (0.12MM)
7025500, 7026226, 7030205, 7030320
Back to top