812770A 1 Mariner SHIM SET


812770A 1 SHIM SET Mariner 7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7A30453VZ, 7A40302UD, 7A40302ZZ, 7A40312UZ, 7A40312ZZ, 7A40412ZZ, 7A41412LB, 7A41452IZ, 7A41452UZ, 7A51412ZZ, 7A51452IZ, 7A60412ZZ, 7A60452IZ, 7E41412ZB, 7E51412ZB, 7E51413VZ, 7E60412Z SHIM
812770A 1 SHIM SET Mariner
Rating:
43

Buy SHIM SET 812770A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Mariner entire parts catalog list:

7050302ED 1996,1997
7050412YD 1991,1992,1993,1994,1995,1996
7055207GD 1998
7055207HB 1999,2000,2001,2002,2003,2004
7055207TF 2005,2006
7060412ET 1996
7A30453VZ 2010
7A40302UD 2006
7A40302ZZ 2006
7A40312UZ 2006
7A40312ZZ 2006
7A40412ZZ 2006
7A41412LB 2002,2003,2004,2005,2006
7A41452IZ 2006
7A41452UZ 2006
7A51412ZZ 2006
7A51452IZ 2006
7A60412ZZ 2006
7A60452IZ 2006
7E41412ZB 2006
7E51412ZB 2006
7E51413VZ 2010
7E60412ZB 2006
7E60413VZ 2010
7E60452IZ 2007
7E60452ZB 2006
7F40203UD 2006
7F40203ZZ 2006
7F40213UZ 2006
7F40452KD 2001
7F40452LB 2002
7F41452KB 2001,2002
7F41452KD 2001

Information:


Illustration 1 g00517891
Simplified Schematic For The Engine Control Switch (ECS)
The engine control switch (ECS) is used by the operator for manually controlling the engine. The ECS has four positions and each position connects to a corresponding input of the GSC+. The selected position of the ECS connects the corresponding input of the GSC+ to the battery negative terminal "B−". At any time, only one of these four positions (inputs) is connected to the battery negative terminal "B−".Each position of the ECS places the engine in a different mode. The four positions and the corresponding modes are described in the following paragraphs."OFF/RESET" - The engine is shut down and the GSC+ is reset. The upper display and fault indicators on the left side are temporarily cleared. The GSC+ turns OFF unless a jumper is installed from the ECS. The jumper electrically connects terminal "6" to terminal "9"."AUTO" - The engine starts and the engine runs when the remote start/stop initiate contact closes the start input that is located on the GSC+. The GSC+ closes the remote start/stop initiate contact to the battery negative terminal "B−". Also, the engine starts and the engine runs when the customer communication module (CCM) sends a remote start command. At this time, the GSC+ starts the engine. The engine runs normally until the remote start/stop initiate contact opens. Also, the engine runs normally until the customer communication module (CCM) sends a remote stop command. The engine enters a cooldown period. After the cooldown period, the engine is shut down. The GSC+ shows diagnostic codes on the upper display and on the fault indicators as the diagnostic code occurs. The GSC+ is ON with the ECS in this position."MAN/START" - The engine starts and the engine runs until the operator turns the ECS to the "OFF/RESET" or the "COOLDOWN/STOP". The engine starts and the engine runs until the GSC+ detects a shutdown fault. The GSC+ shows diagnostic codes on the upper display and on the fault indicators as the diagnostic code occurs. The GSC+ is ON with the ECS in this position."COOLDOWN/STOP" - The engine maintains rated speed for the cooldown period. The cooldown period is programmable from 0 to 30 minutes. After the cooldown period elapses, the engine is shut down. The GSC+ shows diagnostic codes on the upper display and on the fault indicators as the diagnostic code occurs. The GSC+ is ON with the ECS in this position.Note: The remote start/stop contact is connected to the GSC+ start input via a terminal strip. Wire number 57 makes the connection from the terminal strip to the GSC+ start input. Before troubleshooting, disconnect the remote start/stop initiate contacts from the terminal strip.Note: Diagnostic codes are created when the harness connector is disconnected from the GSC+ during these troubleshooting procedures. Clear these created diagnostic codes after the particular problem is corrected and the particular diagnostic code is cleared. The possible causes of a CID 0336 FMI 02 are listed below.
None of the GSC+ inputs from the ECS are connected to ground.
More than one of the GSC+ inputs from the ECS is connected to the battery negative ("B−") at the same time. The one exception is the start input. The start input of the GSC+ is also connected to the remote start/stop initiate contact. The contact is controlled by the customer. The GSC+ will then accept a connection from the battery negative at the start input. Other inputs from the ECS are also received.The CID 0336 FMI 02 is the only ECS diagnostic code that is detected by the GSC+. Clear the diagnostic code from the fault log after troubleshooting is complete. The GSC+ treats a CID 0336 FMI 02 as a shutdown fault. Use these procedures for an active diagnostic code or an inactive diagnostic code.Test Step 1. CHECK FOR AN OPEN CIRCUIT IN THE "OFF/RESET" POSITION
If equipped, disconnect the remote start/stop initiate contacts from the terminal strip in the customer connection box.
Disconnect the harness connector from the GSC+.
Check whether the corresponding contact of the GSC+ harness connector is the only contact that is connected to the battery negative.
At the GSC+ harness connector, measure the resistance from contact "39" to the "B−" terminal of the relay module. Measure the resistance from contacts "32", "33" and "40" to the "B−" terminal. Make a note of the resistances that are measured. Expected Result:The resistance that is measured from contact "39" to the "B−" terminal of the relay module should be 5 ohms or less. The resistance that is measured from contacts "32", "33" and "40" to the "B−" terminal should be greater than 5000 ohms.Results:
OK - All


Parts shim Mariner:

44492A 1
 
44492A 1 SHIM ASSEMBLY
7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075717, 7075D73UY, 7075D73ZY, 7090412TB,
44491A 1
 
44491A 1 SHIM ASSEMBLY
7002201DK, 7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075717, 7075D73UY, 7075D73ZY,
821722
 
821722 SHIM
70404119D, 7050412YD, 7060412ET
812769A 1
 
812769A 1 SHIM SET
7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7A40302UD, 7A40312UZ, 7A41412LB, 7A41452UZ, 7A60412ZZ, 7A60452IZ, 7E60452ZB, 7F40203UD, 7F40213UZ, 7F40452KD, 7F40452LB, 7F41452KB, 7F41452KD
801404875
 
801404875 SHIM
7002201DK, 7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412U
889246A98
 
889246A98 SHIM SET
7A30453VZ, 7A40302ZZ, 7A40312ZZ, 7A40412ZZ, 7A41452IZ, 7A51412ZZ, 7A51452IZ, 7A60412ZZ, 7A60452IZ, 7E41412ZB, 7E51412ZB, 7E51413VZ, 7E60412ZB, 7E60413VZ, 7E60452IZ, 7E60452ZB, 7F40203ZZ
Back to top