16195 Mariner SPRING


16195 SPRING Mariner 7004211SK SPRING
16195 SPRING Mariner
Rating:
83

Buy SPRING 16195 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 9
 

Compatible models:

7004211SK   Mariner

Mariner entire parts catalog list:

7004211SK 1990,1991,1992,1993,1994,1996,1997,1998

Information:

Put a small amount of clean engine oil or glycerine on the lip of seal (4) and in the bores of the O-ring seals at assembly.(1) Distance bearing is installed below pipe surface ... 0.25 0.25 mm (.010 .010 in)(2) Diameter of shaft ... 15.80 0.03 mm (.622 .001 in) Bore in bearings ... 15.88 mm (.625 in)Bore in pipe for bearings ... 18.263 0.013 mm (.7190 .0005 in)(3) Valve assembly shown in the "run" (open) position. When the valve is closed a 0.08 mm (.003 in) feeler gauge must not fit between the valve and the bore in the pipe at any point.(4) Seal. Install the seal with the tip of the seal toward the outside as shown.(5) Diameter of shaft ... 9.60 0.03 mm (.378 .001 in) Bore in the bearing ... 9.80 0.03 mm (.386 .001 in) Adjust shaft as needed to change spring tension until hold-in current consumption (draw) is less than 2 amps at shutdown.(6) 108-2858 Torsion Spring: Free length ... 54.5 0.5 mm (2.15 .02 in)Outside diameter ... 30.36 0.5 mm (1.195 .020 in)(7) 3N7848 Spring: Length under test force ... 22.86 0.5 mm (.90 .02 in)Test force ... 4 N (1 lb)Free length after test ... 35.6 0.5 mm (1.40 .02 in)Outside diameter ... 18.8 0.5 mm (.74 .02 in)(8) Bracket assembly. Bracket assembly must be adjusted so valve assembly (3) is parallel to pipe bore within 2 degrees.(9) 4N3890 Solenoid: Voltage rating ... 24 or 32VCurrent consumption (draw): Pull-in windings ... 39.1A at 38.4VHold-in windings ... .58A at 38.4VPlunger travel ... 11.7 0.3 mm (.46 .01 in)Distance from plunger face to flange face: with solenoid energized* ... 9.6 0.5 mm (.38 .02 in)with plunger extended ... 21.28 0.13 mm (.838 .005 in)*The hold-in current consumption (draw) on engine must take less than 2 amps at shutdown.(10) Diode assembly. Diode assembly required to suppress the back EMF voltage spike generated when the solenoid is turned off.Electric Shutoff Groups
1W1223, 2W6665
Coil resistance at 25°C (77°F) ... 3.33 to 4.07 ohms(1) Distance (reference) between shaft and plate*: 1W1223 Shutoff Group ... 22.68 mm (.893 in)2W6665 Shutoff Group ... 20.62 mm (.812 in)(2) Distance of plunger travel [start with dimension of 11.3 mm (.44 in) at front edge of plate (opposite spring side) to mounting surface on solenoid] ... 15.0 to 16.8 mm (.59 to .66 in)(3) Torque for shaft nut ... 24 7 N m (18 5 lb ft)(4) Torque for terminal nuts ... 1.6 0.3 N m (14 3 lb in)*On engine a test can show need for more adjustment. Hold-in test on engine must take less than 2 amps. The solenoid must be activated to shut off the engine. The maximum activated time is 2.5 minutes.4P0303, 7W7787
4P0303 Shown(1) Solenoid plunger.(2) Stop bolt.(3) Locknut.(4) Lockwire and seal.Coil resistance at 25°C (77°F): Pull-in coil ... 0.560 .056 ohmsHold-in coil ... 21.5 2.2 ohms


Parts spring Mariner:

95383
 
95383 SPRING
7002201DK, 7002201SK, 7003201BK, 7004211SK
16266
 
16266 SPRING
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK
16264
 
16264 SPRING
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF
16195 1
 
16195 1 SPRING
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK, 7F042016B, 7F04201JB
16199
 
16199 SPRING
7004211SK
16212
 
16212 SPRING
7004201HB, 7004201UB, 7004211SK, 7F042016B, 7F04201JB
16215
 
16215 SPRING
7004201HB, 7004201UB, 7004211SK, 7F042016B, 7F04201JB
16216
 
16216 SPRING
7004201HB, 7004201UB, 7004211SK, 7F042016B, 7F04201JB
Back to top