16266004 Mariner SPRING


16266004 SPRING Mariner 7F08201TB SPRING
16266004 SPRING Mariner
Rating:
73

Buy SPRING 16266004 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 37
 

Compatible models:

7F08201TB   Mariner

Mariner entire parts catalog list:

7F08201TB 2005,2006

Information:

1. Turn the crankshaft until "C" mark on the crankshaft gear (1) is in alignment with the "C" mark on the camshaft gear (2).2. Put a mark on the teeth of the accessory drive shaft gear and idler gear at location (A). Put a mark on the teeth of the idler gear and camshaft gear at location (B). This makes correct timing for the camshaft of the fuel injection pump.3. Fasten a hoist to the crankshaft.4. Remove the caps for the crankshaft main bearings.5. Remove the crankshaft. Weight of the crankshaft is 200 lb. (91 kg).6. Remove the crankshaft main bearings from the cylinder block and from main bearing caps.Install Crankshaft
1. Clean the bearing surfaces in the cylinder block. Install the upper halves of main bearings in the block. Put clean SAE 30 engine oil on the bearings.2. Fasten a hoist and put the crankshaft in position in the cylinder block with all the timing marks in alignment.3. Clean the bearing surfaces of the main bearing caps. Install lower halves of the main bearings in the caps. 4. Check the main bearing clearance with wire (A). Install the caps in their respective positions with the number on cap in alignment with the number on the pan face on the left side of the cylinder block.5. Put clean SAE 30 engine oil on the bearing bolt threads and face of the washers. Install the remainder of the bolts and washers. Tighten both bolts to a torque of 30 3 lb.ft. (40.7 4.1 N m). Put a mark on both heads and bearing caps. Tighten each bolt an additional 90° from mark. Remove bearing caps and measure thickness of wire (A). Main bearing clearance must be .0030 - .0059 in. (0.76 - 0.150 mm). Maximum permissible clearance with used parts is .010 in. (0.25 mm).6. Put clean SAE 30 engine on the lower halves of the main bearings. Install the main bearing caps in their respective positions. Install bolts and washers for bearing caps. Tighten both bolts to a torque of 30 3 lb.ft. (40.7 4.1 N m). Put a mark on both bolt head and bearing caps. Tighten each bolt an additional 90° from mark. 7. Check the crankshaft end play that is controlled by the thrust bearing (1) on the rear main bearing with tool group (B). The end play with new bearings must be .0025 - 0.145 in. (0.064 - 0.638 mm). Maximum permissible end play with used bearings is .025 in. (0.64 mm). Install thrust bearing with side that has the identification "BLOCKSIDE" toward the cylinder block.8. If the accessory drive shaft gear, idler gear or camshaft gear has been removed, or if a replacement of the crankshaft gear has been made, it will be necessary to put the accessory drive shaft in time after the engine is assembled. See REMOVE AND INSTALL FUEL INJECTION PUMP HOUSING AND GOVERNOR AS A UNIT.end by: a) install pistonsb) install timing gear coverc) install flywheel housing


Parts spring Mariner:

16264 1
SPRING, (11 mm)
16264 1 SPRING, (11 mm)
7015203KL, 7015203UL, 7040203KL, 7040203UL, 7F08201TB
16264003
 
16264003 SPRING, (14 mm)
7F08201TB, 7F15311ZK
895116
 
895116 SPRING
7F08201TB
75384002
813028003
 
813028003 SPRING
7A25203UK, 7A25213UL, 7A25302UL, 7A3G312UK, 7F08201TB, 7F15311ZK
892777003
 
892777003 SPRING
7F08201TB
892777005
 
892777005 SPRING
7F08201TB
804905001
Back to top