16888 Mariner SPRING


16888 SPRING Mariner 7015203KL, 7015203UL, 7025207UL, 7025217UL, 7030201KL, 7030201UL, 7030211U2, 7030A01UL, 7030A11UL, 7031207LF, 7F042016B, 7F04201JB SPRING
16888 SPRING Mariner
Rating:
98

Buy SPRING 16888 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 43
 

Mariner entire parts catalog list:

7015203KL 2001,2003,2004
7015203UL 2006
7025207UL 2006
7025217UL 2006
7030201KL 2001,2002,2003,2004
7030201UL 2006
7030211U2 2006
7030A01UL 2006
7030A11UL 2006
7031207LF 2002,2003
7F042016B 2006
7F04201JB 2000,2001,2002,2003,2004,2005

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
B 276-1216 Injector Pipe Nut Tool 1
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Note: The following procedure should be adopted to install the fuel injection lines when the electronic unit injectors or the fuel manifold have not been removed. If the electronic unit injectors or the fuel manifold have been removed, refer to Disassembly and Assembly, "Electronic Unit Injector - Install" and Disassembly and Assembly, "Fuel Manifold - Install" for more information.
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Illustration 1 g02177629
Remove plugs from fuel manifold (16) and fuel injection pump (23).
Remove the caps from new fuel injection line (22).
Position fuel injection line (22) onto fuel injection pump (23) and fuel manifold (16). Loosely install nuts for the fuel injection line onto the fuel manifold and the fuel injection pump.
Install bolt (24) and bolt (25) to the tube clip finger tight.
Use Tooling (B) to tighten the nuts on fuel injection line (22) to a torque of 55 N m (41 lb ft).
Tighten bolt (24) and bolt (25) to a torque of 10 N m (88 lb in).Note: Ensure that fuel injection lines do not contact any other engine component.
Illustration 2 g02177712
Illustration 3 g02177628
Follow Step 7 through Step 15 to install fuel injection lines for number one cylinder to number three cylinder.
Install new seal (20) to the electronic unit injector and cylinder head (21). Ensure that the flange on the seal is flush with the cylinder head.
Remove the caps from the port of the electronic unit injector and from the appropriate port in fuel manifold (16).
Loosely connect the nuts at both ends of fuel injection line (12) to the electronic unit injector and to the appropriate port in fuel manifold (16). Ensure that the ends of the fuel injection line are correctly seated in the electronic unit injector and in the fuel manifold.
If no further fuel injection lines are to be installed, follow Step 11.a through Step 11.e to assemble clamp (13) and clamp (15) for the fuel injection lines.
Position rubber separator (25) onto the fuel injection lines.
Position clamp (13) and install bolt (14) finger tight.
Tighten bolt (24) and bolt (22) finger tight.
Illustration 4 g02178062
Ensure that dust seal (27) is seated correctly against seal (20).
Use a suitable tool to install tube clamp (15) to fuel injection lines (12).Note: Ensure that the rubber separator is correctly installed to the fuel injection lines. Ensure that the fuel injection lines do not contact any other engine component.
Use Tooling (B) to tighten the nuts on fuel injection line (22) to a torque of 55 N m (41 lb ft).
Follow Step 8 through Step 12 to install the remaining fuel injection lines.
Tighten bolt (14) and bolt (24) for tube clamp (13) to a torque of 10 N m (88 lb in).
Tighten bolt (22) to a torque of 22 N m (195 lb in).
Follow Step 17 through Step 23 to install fuel injection lines for number four cylinder to number six cylinder.
Install new seal (20) to the electronic unit injector and cylinder head (21). Ensure that the flange on the seal is flush with the cylinder head.
Remove the caps from the port of the electronic unit injector and from the appropriate port in fuel manifold (16).
Loosely connect the nuts at both ends of fuel injection line (19) to the electronic unit injector and to the appropriate port in fuel manifold (16). Ensure that the ends of the fuel injection line are correctly seated in the electronic unit injector and in the fuel manifold.
If no further fuel injection lines are to be installed, follow Step 20.a through Step 20.d to assemble clamp (17) for the fuel injection lines.
Position rubber separator (26) onto the fuel injection lines.
Position clamp (17) and install bolt (18) finger tight.
Tighten bolt (23) finger tight.Note: Ensure that the rubber separator is correctly installed to the fuel injection lines. Ensure that the fuel injection lines do not contact any other engine component.
Illustration 5 g02178062
Ensure that dust seal (27) is seated correctly against seal (20).
Use Tooling (B) to tighten the nuts on fuel injection line (22) to a torque of 55 N m (41 lb ft).
Follow Step 17 through Step 23 to install the remaining fuel injection lines.
Tighten bolt (23) and bolt (18) for tube clamp (17) to a torque of 10 N m (88 lb in).Note: Ensure that the rubber separator is correctly installed to the fuel injection lines.
Illustration 6 g02358237
Position a new gasket (11) onto the cylinder head.
P


Parts spring Mariner:

16212
 
16212 SPRING
7004201HB, 7004201UB, 7004211SK, 7F042016B, 7F04201JB
824994
SPRING, Plate
824994 SPRING, Plate
70152374D, 7016207CD, 7020201HB, 7020201TB, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7A30302LB, 7A40302UD, 7A40312U
821784
 
821784 SPRING
7031203GD, 7031207CD, 7031207LF, 7041203GB
804366
SPRING
804366 SPRING
7004201HB, 7004201UB, 7F04201JB
803554
 
803554 SPRING
7F02201ZK, 7F042016B, 7F04201JB
804366001
 
804366001 SPRING, Starter Lock Cam
7F042016B, 7F04201JB
803746 1
 
803746 1 SPRING
7015203KL, 7015203UL
803788
 
803788 SPRING
7015203KL, 7015203UL
Back to top