82101M Mariner SPRING, CLAMP BRACKET BOLT


82101M SPRING, CLAMP BRACKET BOLT Mariner 7010209, 7015207, 7015307, 7015327, 7015529, 7025200, 7025500, 7028207, 7028527, 7030200 SPRING
82101M SPRING, CLAMP BRACKET BOLT Mariner
Rating:
63

Buy SPRING, CLAMP BRACKET BOLT 82101M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 27
 

Mariner entire parts catalog list:

7010209 1979,1983,1984,1985,1986
7015207 1977
7015307 1977
7015327 1987
7015529 1979
7025200 1980
7025500 1980
7028207 1977
7028527 1977
7030200 1980

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
B 8T-0890 Puller Group 1
C 8T-5096 Dial Indicator Group 1
Illustration 1 g00810377
(1) Centrifugal oil filter
(2) Valve
(3) Camshaft cover
Illustration 2 g00810333
(4) Bearing
(5) Nut
(6) Stiffener plate
(7) Nut
(8) Rotor cover
(9) Cover
(10) Paper liner
(11) Spindle
(12) Stand tube
(13) O-ring
(14) O-ring
(15) Bearing
(16) Clamp
(17) Rotor base
(18) Filter body
Close valve (2) to centrifugal oil filter (1).
Loosen clamp (16) and nut (5). Remove cover (9) from filter body (18).
Remove O-ring seal (14) from the body.
Remove the rotor assembly from spindle (11). Lift the rotor assembly carefully so the bearings are not damaged.
Use tool (A) to hold the rotor assembly and remove nut (7).
Remove stiffener plate (6).
Use tool (B) to remove rotor cover (8) from rotor base (17). Remove O-ring seal (13) from the base. Remove paper liner (10) from the rotor cover. Properly dispose of the paper liner. Use a plastic scraper to clean out the inside of rotor cover (8).
Remove stand tube (12) from rotor base (17) and clean the stand tube.
Clean the nozzles in rotor base (17). Do not enlarge the nozzles.
Inspect bearings (4) and (15) for excessive wear.
Inspect spindle (11) for excessive wear.
If there is minimal wear to bearing (4), bearing (15), and spindle (11) go to step 14. If there is considerable wear to bearing (4), bearing (15), and spindle (11) go to step 13.
Use tool (C) to measure the clearances between the bearing (4) and bearing (15) and spindle (6). The maximum clearance between bearing (4) and spindle (11) is 0.25 mm (0.010 inch).The maximum clearance between bearing (15) and spindle (11) is 0.20 mm (0.008 inch).If the rotor bearings and the spindle are not within specifications, replace the parts.Note: The spindle and the filter body are replaced as a complete assembly. The rotor assembly is replaced as a complete assembly.Before you assemble the centrifugal oil filter, thoroughly clean all of the parts and inspect all of the parts. Replace parts that are damaged or worn.
Ensure that all of the rotor components are thoroughly clean before assembling the rotor. Failure to do so can cause an out of balance condition that can cause rapid wear to the bearings and the spindle.
Install stand tube (12) on rotor base (17).
Install a new paper liner (10) in rotor cover (8). Place O-ring seal (13) on rotor base (17). Position rotor cover (8) on rotor base (17).
Install stiffener plate (6).
Use tool (A) to hold the rotor assembly and install nut (7).
Install the rotor assembly on spindle (11). Install the rotor assembly carefully so the bearings are not damaged.
Install O-ring seal (14) on filter body (18).
Install cover (9) and clamp (16) on filter body (18). Tighten clamp (16) and nut (5).
Open valve (2) to centrifugal oil filter (1).
Check the centrifugal oil filter for leaks. Feel the centrifugal oil filter for excessive vibration.


Parts spring Mariner:

80575M
 
80575M SPRING
7005207, 7005227, 7008218EW, 7008425, 7015207, 7015307, 7015327, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527
82099M
 
82099M SPRING
7003207, 7005207, 7005227, 7008238, 7008247, 7015207
80193M
 
80193M SPRING, THROTTLE STOP SCREW
7008218EW, 7008425, 7015207, 7015307, 7015327
80194M
 
80194M SPRING, CHOKE PLUNGER
7008218EW, 7008425, 7015207, 7015307, 7015327
82104M
SPRING, REVERSE LOCK
82104M SPRING, REVERSE LOCK
7015207, 7015307, 7015327
82115M
 
82115M SPRING, STARTER
7008208, 7008218EW, 7008238, 7008248, 7008425, 7010209, 7015529, 7028207, 7028527
81103M
SPRING, PAWL
81103M SPRING, PAWL
7028207, 7028527
83488M
 
83488M SPRING
7008204, 7008208, 7008226, 7010209, 7015529, 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716
Back to top