82110M Mariner SPRING


82110M SPRING Mariner 7003207, 7004201, 7005201, 7005207, 7005227, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425 SPRING
82110M SPRING Mariner
Rating:
103

Buy SPRING 82110M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Mariner entire parts catalog list:

7003207 1987
7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7005227 1977
7008208 1978
7008218EW 1996,1998
7008238 1978
7008247 1977,1987
7008248 1978
7008305 1985,1986
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9352 Engine Stand 1
8T-2826 Head Adapter 1
B - Fabricated Plate (1) 1
- Fabricated Plate (2) 1
8T-2679 Valve Guide Rod 1
1D-4720 Nut 2
C 8T-2660 Valve Spring Compressor 1
515–1161 Valve Spring Compressor Tool (3) -
8F-6350 Bolt 1
5B-2638 Bolt 1
4B-5271 Washer 1
F 8T-2676 Valve Guide Driver 1
J 4C-8540 Dowel Driver 1
K 4C-8769 Valve Seat Driver 1
L 8T-2674 Valve Seat Driver 1
M FT-1741 Vacuum Tester 1
N 4C-9500 Quick Cure Primer -
P 4C-9507 Retaining Compound -
Q 8T-2998 Lubricant -
(1) Fabricate the plate from 6.4 mm (0.25 inch) flat stock. The outside dimensions of the plate are 32 mm (1.25 inch) by 133 mm (5.25 inch). Drill a 16.5 mm (0.65 inch) hole in the center.
(2) Fabricate the plate from 6.4 mm (0.25 inch) flat stock. The outside diameter is 203 mm (8 inch). Drill a 16.5 mm (0.65 inch) hole in the center.
(3) This tool is an alternative Valve Spring Compressor Tool.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install the cylinder head on Tooling (A). The weight of the cylinder head is approximately 205 kg (450 lb).
If the O-ring seals were removed from the valve guides, install new O-ring seals in the valve guides.
Illustration 1 g01213114
Lower the temperature of bridge dowels (11) to −70 °C (−94 °F). Use Tooling (J) to install the bridge dowels to a height of Dimension (Y) above the cylinder head. Dimension (Y) is 105 2.0 mm (4.1 0.08 inch).
Illustration 2 g01213116
Lower the temperature of valve guides (9) to −70 °C (−94 °F). Use Tooling (F) to install the valve guides to a height of Dimension (W) above the cylinder head. Dimension (W) is 20 2.0 mm (0.8 0.08 inch).The correct inside diameter of the valve guide after installation is 16.031 0.028 mm (0.6311 0.0011 inch).
Do not use a hammer to install the valve seats. The use of a hammer will damage the valve seats and the cylinder head. Only use a suitable press for installation of the valve seats.
Illustration 3 g01213121Note: Do not lower the temperature of valve seats (8). Make sure that the valve seats are at room temperature before installation.
Apply Tooling (N) to the outside of the valve seats. Then apply Tooling (P) over Tooling (N).
Use Tooling (K) and a suitable press to install the valve seats for the inlet valves. Press the valve seats into the bottom of the counterbore in the cylinder head.
Use Tooling (L) and a suitable press to install the valve seats for the exhaust valves. Press the valve seats into the bottom of the counterbore in the cylinder head.
Inspect valves (7). If necessary, use a fine stone that is properly dressed for grinding the faces of valves (7). Grind the valves only enough to restore the faces.
Lubricate valves (7) with Tooling (Q). Install valves (7) into the original positions in the cylinder head.


Parts spring Mariner:

80329M
 
80329M SPRING, PILOT ADJUSTING
7002200, 7004201, 7005201, 7005207, 7008208, 7008238, 7008248, 7008305, 7020201, 7025207PW, 7028527, 7030200, 7030205, 7030301
80575M
 
80575M SPRING
7005207, 7005227, 7008218EW, 7008425, 7015207, 7015307, 7015327, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527
80056M
 
80056M SPRING
7003207, 7005207, 7005227
80058M
 
80058M SPRING
7003207, 7005207, 7005227
80437M
 
80437M SPRING, AIR ADJUSTING SCREW...
7008238, 7008247, 7040207PW, 7040208PW, 7F08203HF, 7F08261DF
82084M
 
82084M SPRING, SHIFT LEVER CAM...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7040202, 7040206, 7040207, 7040208, 7040328, 7040507, 7040706, 7040716
96203
 
96203 SPRING, PILOT CONTROL SCREW - EARLY STYLE
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7010207HB, 7010312DT, 7011201TB, 7015201LD, 70152374D, 7016207CD, 7020201HB, 7020201TB, 7020207, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB,
96575M
 
96575M SPRING
7008208, 7008238, 7008248
Back to top