812640 Mariner STARTER HANDLE


812640 STARTER HANDLE Mariner 7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK STARTER
812640 STARTER HANDLE Mariner
Rating:
8

Buy STARTER HANDLE 812640 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$198.95
 

21-06-2024
11.75[5.29] Pounds
US: Race-Driven Inc
Brake Rotors & Pads for Polaris General 1000 Sport 2020-2023 Front & Rear MudRat
Race-Driven Race-Driven Front and Rear MudRat Brake Rotors and MudRat Sintered Metal Brake Pads || Race-Driven exclusive sintered metal compound brake pads are designed to withstand extreme conditions || MudRat Rotors are a vented rotor to provide maximum air flow to cool down brakes || Fits: 2020 2021 2022 2023 Polaris General 1000 Sport
$171.09
 

28-09-2020

-: -
The Hillman Group 812640 Hot Dipped Galvanized Carriage Bolt, 1/2-Inch x 14-Inch, 25-Pack by The Hillman Group
$85.99
 

13-04-2023
17.42[7.84] Pounds
-: -
Hillman Group Galvanized Carriage Bolt 1/2" x 14”, 25 Count, Blunt Point, Alloy Steel, Self-Locking Round Head Fasteners, for Wood and Metal, No Washer Needed, Rust-Resistant (812640)
Carriage Bolts are designed to fasten a wooden face to either wood or metal || Flat head provides a semi-flush finish to applications || The heads is designed to eliminate the need for a washer || Square underside of the head is self locking to eliminate the need for a driving tool || Galvanized finish is perfect for rust prevention
Number on catalog scheme: 11
 

Compatible models:

Mariner entire parts catalog list:

7004201HB 1999,2000,2001,2002,2003,2004,2005
7004201UB 2006
7004211SK 1990,1991,1992,1993,1994,1996,1997,1998
7006201MK 2003,2004
7006201UK 2006

Information:

1. Disconnect air inlet temperature sending unit (1).2. Disconnect oil lines (2) and (3) at the air shutoff hydraulic cylinder. 3. Loosen clamp (4) and move the clamp away from the pipe connection. 4. Remove the bolts that hold air shutoff (5) to the air inlet manifold and remove the pipe and air shutoff (5).
Put a cover over the air inlet manifold opening so foreign material will not get into the air inlet manifold.
5. Put a mark for alignment on pipe (6) and air shutoff (5).6. Remove pipe (6) from air shutoff (5).Install Air Shutoff Group
1. Put a light coat of engine oil on the O-ring seals on pipe (1).
Be sure to remove the cover over the air inlet manifold opening before installation of the air shutoff.
2. Make an alignment of the marks on pipe (1) and shutoff (2) and install pipe (1) in shutoff (2).3. Put air shutoff (2) and pipe on inlet manifold. Use a new gasket. 4. Put clamp (3) in position. Put 5P3931 Anti-Seize Compound on the threads of the clamp. Tighten the clamp nut to a torque of 10 2 lb.ft. (14 3 N m). 5. Connect hydraulic lines (5) and (6) to air shutoff (2).6. Connect air inlet temperature sending unit (4).Disassemble Air Shutoff Group
start by:a) remove air shutoff 1. Remove hydraulic cylinder (1).
Plate assembly (2) is connected to a shaft and spring which turns plate assembly (2) to the closed position. To prevent personal injury and component damage, use the knob to hold plate assembly (2) open while the bolts are removed.
2. Remove plate assembly (2). 3. Remove knob (3). 4. Remove cover (4). 5. Remove shaft (5). 6. Make reference marks on shaft (5), spring (6) and latch (8) for correct assembly.7. Remove dowel (7) and remove latch (8) and spring (6). 8. Use tool (A) to remove the seal from cover (4).Assemble Air Shutoff Group
1. Use tool (A) to install the seal in cover (1). Install the seal with the spring loaded lip toward the inside of the air shutoff. 2. Install washer and spring (3) and latch (5) on shaft (2). Be sure latch (5) and spring (3) are in correct alignment with shaft (2). Install dowel (4) to hold latch in place. 3. Put shaft (2) in housing assembly (6). Be sure the end of spring (3) engages with the hole in housing assembly (6). When correctly assembled, clockwise rotation of shaft (2) will be against spring force. 4. Put a light coat of engine oil on the seal in cover (1) and install cover (1) on housing assembly (6). 5. Put knob (7) on shaft (2). 6. Turn knob (7) in a clockwise direction against the spring and install plate assembly (8). Tighten the three bolts and bend the sheet metal lock against the bolts. 7. Tighten the nut that holds cylinder (9) to the flange to a torque of 33 5 lb.ft. (45 7 N m).8. Use a new O-ring seal and install hydraulic cylinder (9). Put the cylinder in position so that the plunger is free and tighten the bolts, first one then the other, in small amounts to prevent distortion of the flange.end by:a) install air shutoff


Parts starter Mariner:

812632
STARTER HOUSING
812632 STARTER HOUSING
7004201HB, 7004201UB, 7004211SK, 7F04201JB
812633
STARTER SHEAVE
812633 STARTER SHEAVE
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK, 7F04201JB
16110 3
16110 1
 
16110 1 STARTER PLATE
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7F04201JB
812639
812642
STARTER PULLEY
812642 STARTER PULLEY
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK, 7F04201JB
17634
 
17634 STARTER LOCK
7004201HB, 7004201UB, 7004211SK, 7006201MK, 7006201UK, 7015203KL, 7015203UL, 7F04201JB
804975A 1
 
804975A 1 STARTER MOTOR KIT
7006201MK, 7006201UK
Back to top