83305M Mariner STOP, MAGNETO BASE


83305M STOP, MAGNETO BASE Mariner 7025200, 7025500, 7028207, 7028527 STOP
83305M STOP, MAGNETO BASE Mariner
Rating:
98

Buy STOP, MAGNETO BASE 83305M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 31
 

Compatible models:

Mariner entire parts catalog list:

7025200 1980
7025500 1980
7028207 1977
7028527 1977

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-0960 Handling Tool Group 1
B 191-5323 Cylinder Group 2
191-5326 Bushing 2
C 191-5335 Support (Main Bearing) 2
D 191-5347 Hydraulic Pump (Pneumatic) 1
229-9453 Accessory Group (Pump) 1
E 134-0932 Main Bearing Driver 1
F 4C-9818 Hex Adapter(1) 1
4C-9819 Universal Joint(1) 1
213-3110 Socket(1) 1
4C-9927 Drill(1) 1
G 3P-1529 Circular Level 1
H 4C-5593 Anti-Seize Compound 1
(1) This Tooling is available for rotating the engine.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The bearing has a locating tab. When the bearing is viewed from the flywheel, counterclockwise rotation is required for the installation of the upper half of the bearing. Ensure that the tab is properly seated in the groove. Ensure that the tab does not break in the groove.Note: If the main bearing cap bolts were removed, use a tap in order to clean the threads in the cylinder block prior to the installation of the bolts. Tighten the bolts to a torque of 100 20 N m (75 15 lb ft).
Illustration 1 g00955403
Install thrust plates (7). If necessary, carefully pry the crankshaft in order to roll the thrust plates into position in the cylinder block. Note: On the G3606 Engine and the G3612 Engine, install thrust plates (7) on the Number 7 main bearing for the rear driven equipment. Install thrust plates (7) on the Number 1 main bearing for the front driven equipment.Note: On the G3608 Engine and the G3616 Engine, install thrust plates (7) on the Number 9 main bearing for the rear driven equipment. Install thrust plates (7) on the Number 1 main bearing for the front driven equipment.
Illustration 2 g00955401
Illustration 3 g00955566
Put clean engine oil on upper main bearing (6). Use Tooling (E) in order to roll upper main bearing (6) into the cylinder block. Note: On the G3606 Engine and the G3612 Engine, the Number 4 main bearing journal does not have an oil hole. Tooling (E) cannot be used in order to roll the upper main bearing (6) in the cylinder block. Push the upper main bearing (6) in position with your hand.Note: On the G3608 Engine and the G3616 Engine, the Number 5 main bearing journal does not have an oil hole. Tooling (E) cannot be used in order to roll the upper main bearing (6) in the cylinder block. Push the upper main bearing (6) in position with your hand.
Illustration 4 g00955574
Use a clean cloth to wipe lower main bearing (5) and the bore in main bearing cap (4). Ensure that there is no thread lubricant on lower main bearing (5) or main bearing cap (4). Install lower main bearing (5) in main bearing cap (4). Ensure that the tab on the back of lower main bearing (5) is engaged with the slot in main bearing cap (4).
Put clean engine oil on lower main bearing (5). Be sure not to put the engine oil on the back side of lower main bearing (5).
Use Tooling (A) in order to position main bearing cap (4).
Ensure that dowel (8) engages with the hole in the cylinder block. The dowel should extend 10.0 0.5 mm (0.39 0.020 inch) from main bearing cap (4).
Illustration 5 g00955590
Install nuts (3) and the washers to studs (2) in order to hold main bearing cap (4) in position. Remove Tooling (A) from main bearing cap (4).


Parts stop Mariner:

81662M
 
81662M STOP SWITCH (MANUAL)
7028207, 7028527
81663M
 
81663M STOP SWITCH ASS'Y
7028207, 7028527
81580M
 
81580M STOP, MAGNETO BASE
7028207, 7028527
80628M
 
80628M STOP, MAGNETO BASE
7025200, 7025207PW, 7025500, 7028207, 7028527
84885M
STOP, MAGNETO BASE
84885M STOP, MAGNETO BASE
7028527, 7030200, 7030205, 7030320
94652M
 
94652M STOP, MAGNETO BASE
7028527, 7030200
84916M
 
84916M STOP SWITCH ASSEMBLY (SEE NOTE)
7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301
97754M
 
97754M STOP SWITCH ASSEMBLY - REMOTE
7008204, 7008208, 7008226, 7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207PW, 7040208PW, 7040706, 7040716
Back to top