898006 STRAP, Retaining Mariner
7F75413TD
STRAP
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
![Auto Ventshade [AVS] Aerocab Pro Marker Light | Fits 1999-2016 Ford F-250, F-350, F-450, Textured Matte Black, 1 pc. | 898006](http://c1.a2109.com/_150/aws_api/41g/41g7o/41g7otrn9nl.jpg)
Auto Ventshade [AVS] Aerocab Pro Marker Light | Fits 1999-2016 Ford F-250, F-350, F-450, Textured Matte Black, 1 pc. | 898006
Auto Ventshade (AVS) ๐๐๐ง๐ ๐๐ก๐งโ 1999 - 2016 Ford F-250, F-350, F-450 || ๐๐๐ ๐ ๐๐ฅ๐๐๐ฅ ๐๐๐๐๐ง๐ฆโFeatures a continuous LED light bar with sweeping motion for turn signals and hazard lights. || ๐๐จ๐ฆ๐ง๐ข๐ ๐๐๐งโCustom-molded to match the contours of your vehicleโs cab. Instantly adds a custom look to your ride. || ๐๐๐ฆ๐ฌ ๐๐ก๐ฆ๐ง๐๐๐๐๐ง๐๐ข๐กโMounts in minutes with 3M automotive grade adhesive mounting tape or mechanical (included). || ๐๐จ๐ฅ๐๐๐๐โMade from ultra-tough Dura-Flex 2000 TPO. Covered by the AVS three-year warranty and made in the USA with global materials.
Auto Ventshade (AVS) ๐๐๐ง๐ ๐๐ก๐งโ 1999 - 2016 Ford F-250, F-350, F-450 || ๐๐๐ ๐ ๐๐ฅ๐๐๐ฅ ๐๐๐๐๐ง๐ฆโFeatures a continuous LED light bar with sweeping motion for turn signals and hazard lights. || ๐๐จ๐ฆ๐ง๐ข๐ ๐๐๐งโCustom-molded to match the contours of your vehicleโs cab. Instantly adds a custom look to your ride. || ๐๐๐ฆ๐ฌ ๐๐ก๐ฆ๐ง๐๐๐๐๐ง๐๐ข๐กโMounts in minutes with 3M automotive grade adhesive mounting tape or mechanical (included). || ๐๐จ๐ฅ๐๐๐๐โMade from ultra-tough Dura-Flex 2000 TPO. Covered by the AVS three-year warranty and made in the USA with global materials.
$6.09
28-09-2017
.19[0.00] pounds
MERCURY: MERCURY
Mercury Quicksilver 898006 Strap Made by Mercury Quicksilver
Number on catalog scheme: 37
Compatible models:
7F75413TD
Mariner
Mariner entire parts catalog list:
Information:
1. Check each bearing cap (1) for its location on the engine. Each cap has an arrow which is toward the front of the block and a number which gives the location of that cap. Keep each bearing with the correct cap. 2. Remove bearing caps No. 2 through No. 4. Remove thrust plates from No. 3 upper bearing.
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 450° F (233° C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2). 4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS. 6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block.8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block. 9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows:a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.006 to 0.020 in. (0.152 to 0.508 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump
Be careful not to cause damage to the crankshaft journals when the crankshaft is removed.
3. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft as shown. Remove No. 1 and No. 5 main bearing caps. Remove the crankshaft. Weight of the crankshaft is 270 lb. (122 kg). 4. Remove crankshaft gear (2) with tooling (A).5. Remove dowel and pin from crankshaft with tooling (B).Install Crankshaft
1. Install pin (1) in the crankshaft end until it is extended from the surface 0.025 0.02 in. (6.4 0.5 mm).2. Install dowel (2) until it is extended from the surface 0.16 0.02 in. (4.1 0.5 mm). 3. Heat crankshaft gear (3) to a maximum temperature of 450° F (233° C). Install gear (3) on the crankshaft with groove (4) in alignment with dowel (2). 4. Make sure the upper main bearings are clean. Put clean oil on the upper main bearings and journals of the crankshaft.
Do not cause damage to the crankshaft journals. Make sure the "V" mark on the crankshaft gear is in alignment with the "V" mark on the idler gear.
5. Install one of the flywheel bolts in each end of the crankshaft. Fasten a hoist to the crankshaft and put it in position in the block. For more detail about installation of main bearings see REMOVE AND INSTALL CRANKSHAFT MAIN BEARINGS. 6. Check the bearing clearance with Plastigage.7. Put clean engine oil on the bolts for caps No. 1 and No. 5. Install No. 1 and No. 5 caps with the bolts finger tight. Make sure the arrows on the caps are toward the front of the block.8. Install thrust plates (5) for the No. 3 upper main bearing. Install the thrust plates with the side that has the identification "Block Side" toward the cylinder block. 9. Put clean oil on the bolts for caps No. 2 through No. 4. Install caps No. 2 through No. 4 with the bolts finger tight. Make sure the arrows are toward the front of the block.10. Tighten the cap bolts as follows:a) Tighten the bolts on the tab end of the caps first to a torque of 190 10 lb.ft. (260 14 N m).b) Tighten the bolts on the other end of the caps to a torque of 190 10 lb.ft. (260 14 N m).c) Put a mark across the bolt head and cap. Tighten the bolts opposite the tab end 120°. Tighten the bolts on the tab end of the cap 120°. 11. Check the play of the crankshaft with tool (A). Make sure the dial indicator is against a machined surface. End play for new thrust plates must be 0.006 to 0.020 in. (0.152 to 0.508 mm). The maximum end play with used thrust plates is 0.035 in. (0.89 mm).end by:a) install pistonsb) install flywheel housingc) install timing gear coverd) install oil pump