88798A 2 Mariner SWIVEL PIN ASSEMBLY (LONG SHAFT) - MANUAL


88798A 2 SWIVEL PIN ASSEMBLY (LONG SHAFT) - MANUAL Mariner 7045217, 7050200, 7050716, 7050717, 7060312PC SWIVEL
88798A 2 SWIVEL PIN ASSEMBLY (LONG SHAFT) - MANUAL Mariner
Rating:
13

Buy SWIVEL PIN ASSEMBLY (LONG SHAFT) - MANUAL 88798A 2 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

Compatible models:

Mariner entire parts catalog list:

7045217 1987,1988,1989
7050200 1980,1982,1983,1985,1986
7050716 1986
7050717 1987,1988,1989,1990
7060312PC 1989

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-5598 Anti-Seize Compound -
B 195-4609 Seal Pick 1
C - Isopropyl Alcohol -
D 5P-4996 Plug 2 Start By:
Remove the Exhaust Elbow.
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
Illustration 1 g02151651
Disconnect clamp assembly (1).
Remove three bolts (3).
Remove bolt (4). Remove tube assembly (2) and the gasket.
Illustration 2 g02583797Note: Cap all tube assemblies and fittings that are disconnected to prevent fluid loss. This action will also keep contaminants out of the systems.
Disconnect tube assemblies (5) and (6). Plug tube assemblies (6) with Tooling (D).
Illustration 3 g02153363
Disconnect cable assembly (7) and cable assembly (8).
Remove allen bolt (9), the clamp assembly, and position cable assembly (10) out of the way.
Disconnect flame detection temperature sensor (11).
Illustration 4 g02153382
Remove nuts (16) and remove combustion head (15).
Remove gasket (14), tube assembly (13), and gasket (12).Note: The gaskets are for one time use only. Replace with new gaskets upon installation.
If required, remove studs (17).
Illustration 5 g02153383
Remove fittings (18) and (19).
Remove spark plug (20) and remove fitting (21).
Illustration 6 g02481277
Use Tooling (B) to remove O-ring seals (22) and (23) from cable assembly (10). Discard the O-ring seals.Installation Procedure
Install combustion head (15) in reverse order.
Apply Tooling (A) onto the threads of studs (17). Install the studs. Tighten studs (17) to a torque of 17 2 N m (150 18 lb in).
Apply Tooling (A) onto the threads of the studs and nuts (16). Tighten nuts (16) in a crisscross pattern to a torque of 23 3 N m (17 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft). Tighten nuts (16) again in a crisscross pattern to a torque of 28 3 N m (21 2 lb ft).
Use caution when you are using isopropyl alcohol. Avoid prolonged skin contact with isopropyl alcohol.Vapors may be harmful if inhaled. Use only in a well ventilated area. Do not smoke while using isopropyl alcohol.Isopropyl alcohol is flammable. Do not use near an open flame or near welding operations. Keep isopropyl alcohol away from heated surfaces exceeding 482°C (900°F).
Note: This connection is an electrical connection and cannot be lubricated with a petroleum-based lubricant. Isopropyl alcohol is the only approved lubrication for this connection.
Lubricate new O-ring seals (22) and (23) with Tooling (C) prior to installation.
Tighten fitting (21) to a torque of 60 6 N m (44 4 lb ft).
Tighten fittings (19) and (18) to a torque of 30 2 N m (266 18 lb in).
Tighten spark plug (20) to a torque of 57.5 4 N m (42 3lb ft).
Apply Tooling (A) to the threads of flame d


Parts swivel Mariner:

69540A 3
 
69540A 3 SWIVEL PIN AND STEERING ARM ASSEMBLY (SHORT SHAFT)
7045217, 7050200, 7050716, 7060312PC, 7060524, 7070509
69540A 4
 
69540A 4 SWIVEL PIN AND STEERING ARM ASSEMBLY (LONG SHAFT)
7045217, 7050200, 7050716, 7060312PC, 7060524, 7070509, 7070520
77013A 1
 
77013A 1 SWIVEL, LINK ROD TO THROTTLE CONTROL LEVER
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520, 7090520, 7090524, 7090529, 7115520, 7115529, 7140629
8597A 4
 
8597A 4 SWIVEL BRACKET (SHORT SHAFT)
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524
8599A 6
 
8599A 6 SWIVEL BRACKET (LONG SHAFT)
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070520
88798A 1
 
88798A 1 SWIVEL PIN ASSEMBLY (SHORT SHAFT) - MANUAL
7045217, 7050200, 7050716, 7050717, 7060312PC
57440
 
57440 SWIVEL, LINK ROD TO THROTTLE ACTUATOR
70404119D, 7045217, 7050200, 7050716
8710A17
 
8710A17 SWIVEL BRACKET ASSEMBLY
7045217, 7075312ND, 71354120D, 7135417PD, 7150453PD, 7175412PD, 7200412PD
Back to top