817518 Mariner TEE


817518 TEE Mariner 7115F13KD, 7115F13RD, 7115F13UF, 7200473GD, 7250422PD, 7F75411JD, 7F75412RD, 7F75413TD TEE
817518 TEE Mariner
Rating:
58

Buy TEE 817518 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
£372.15
 

02-10-2017
57.32[25.65] pounds
VALEO SERV: VALEO SERVICE
Valeo Service 817518 Evaporator
$762.97
 

26-09-2017

Flowmaster: Flowmaster
FLOWMASTER 817518 Exhaust System Kit 2010-2010 Ford Mustang
Type - Cat-Back||Diameter - 2-1/4 in.||Exit Position - Rear Exit||Exhaust Type - Dual||Includes Muffler - Yes
$762.97
 

02-10-2017

Flowmaster: Flowmaster
Flowmaster 817518 Super 60 Series Cat-Back Exhaust System for Ford Mustang 4.0L V6 Engine
Mandrel bent 16 gauge stainless steel tubing||Mild to Moderate Sound exterior exhaust tone||Includes hangers and hardware for easy installation||Connects After Factory Catalytic Converter
Number on catalog scheme: 15
 

Mariner entire parts catalog list:

7115F13KD 2001,2002,2003
7115F13RD 2004,2005
7115F13UF 2006
7200473GD 1998
7250422PD 1989,1990,1991,1992,1993,1994
7F75411JD 2000,2001,2002,2003
7F75412RD 2004,2005
7F75413TD 2005,2006

Information:

Starting Motor
Illustration 1 g01964824
Typical example
12 V 4 kW Starting Motor
(1) Terminal 30 for connection of the battery cable
(2) Terminal 50 for connection of ignition switch
(3) Terminal 31 for connection of the ground
Illustration 2 g01964833
Typical example
24 V 5.5 kW Starting Motor
(4) Terminal 30 for connection of the battery cable
(5) Integrated Magnetic Switch (IMS)
(6) Terminal 50 for connection of ignition switch
(7) Terminal 31 for connection of the ground The starting motor turns the engine via a gear on the engine flywheel. The starting motor speed must be high enough in order to initiate a sustained operation of the fuel ignition in the cylinders.The starting motor consists of the main armature and a solenoid. The solenoid is a relay with two windings Pull-In (PI) and Hold-In (HI). Upon activation of ignition switch, both windings move the iron core by electromagnets. The linkage from the iron core acts to move the pinion toward the flywheel ring gear for engagement. Upon complete engagement, the solenoid completes the high current circuit that supplies electric power to the main armature in order to provide rotation. During cranking of the engine, only the Hold-In (HI) winding is active.The ignition switch is deactivated once the desired engine speed has been achieved. The circuit is disconnected. The armature will stop rotating. Return springs that are located on the shafts and the solenoid will disengage the pinion from flywheel ring gear back to the rest position.The starting motor has an overrunning clutch to prevent damage to the starting motor and mechanical transmissions as the engine speed increases.Certain higher powered starting motors are designed with an Integrated Magnetic Switch (IMS). The Integrated Magnetic Switch (IMS) is activated by the ignition switch. The solenoid circuit then engages the starting motor. The benefit of Integrated Magnetic Switch (IMS) is a lower current in the ignition circuit that will allow the engine ECM to control ignition without the use of a relay.Alternator
The electrical outputs of the alternator have the following characteristics:
Three-phase
Full-wave
RectifiedThe alternator is an electro-mechanical component. The alternator is driven by a belt from the crankshaft pulley. The alternator charges the storage battery during the engine operation.The alternator is cooled by an external fan which is mounted behind the pulley. The fan may be mounted internally. The fan forces air through the holes in the front of the alternator. The air exits through the holes in the back of the alternator.The alternator converts the mechanical energy and the magnetic field into alternating current and voltage. This conversion is done by rotating a direct current electromagnetic field on the inside of a three-phase stator. The electromagnetic field is generated by electrical current flowing through a rotor. The stator generates alternating current and voltage.The alternating current is changed to direct current by a three-phase, full-wave rectifier. Direct current flows to the output terminal of the alternator. The direct current is used for the charging process.A regulator is installed on the rear end of the alternator. Two brushes conduct current through two slip rings. The current then flows to the rotor field. A capacitor protects the rectifier from high voltages.The alternator is connected to the battery through the ignition switch. Therefore, alternator excitation occurs when the switch is in the ON position.


Parts tee Mariner:

42425
 
42425 TEE
7002201DK, 71354120D, 7135412AD, 7135417PD, 7135826, 7150453ND, 7150453PD, 7150629, 7175412PD, 7175413AD, 7175413PD, 7175413YD, 7175629, 7200412PD, 7200620, 7220727, 7250422PD
42425 1
 
42425 1 TEE
70404119D, 7135417PD, 7135826, 7150453ND, 7150453PD, 7175412PD, 7175629, 7200412PD, 7200620, 7250422PD
59169
 
59169 TEE, CRANKCASE BLEED HOSE
7006201CD, 7008218EW, 7008237, 7010312DT, 7031203GD, 7031207CD, 70404119D, 70432037D, 7050302ED, 7050412YD, 7050716, 7050717, 7055207GD, 7060312PC, 7060412ET, 7060524, 7070520, 7075217CD, 7100412CD, 7150413ED, 7175413AD, 7175413PD, 7175413YD, 7220727
13033
 
13033 TEE FITTING
7100412CD, 7100412HB, 7100412NC, 7115412TB, 7200473GD, 7250422PD
818993
 
818993 TEE
7002201DK, 7031203GD, 7031207CD, 70404119D, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7135412AD, 7135412E
91836
 
91836 TEE
7250422PD
875268
 
875268 TEE FITTING
7F75411JD, 7F75412RD
Back to top