811216 Mariner THROTTLE VALVE, 90


811216 THROTTLE VALVE, 90 Mariner 7050412YD, 7060412ET, 7075312SD THROTTLE
811216 THROTTLE VALVE, 90 Mariner
Rating:
63

Buy THROTTLE VALVE, 90 811216 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
 

21-04-2021

-: -
Sulfate Standard, 1000 ppm SO4²-
Ready to use || Certificates of Analyses and MSDS are available from manufacturer || NIST traceable where NIST standards exist
$126.00
 

13-11-2022
22.52[10.13] Pounds
-: -
GSP 811216 Complete Loaded Strut and Coil Spring Assembly - Left or Right Rear (Driver or Passenger Side)
GSP Loaded Strut Assemblies come complete with high quality struts, coil springs, strut mounts, and hardware and are ready to install, right out of the box, making installation quicker and easier || All new components, engineered to provide OE form, fit, and function, are used to manufacture our loaded strut assemblies, ensuring that ride comfort and handling are returned to factory fresh levels || Struts feature hi-performance 'Tri-Lock' PTFE piston rod seals, chrome plated piston rods, and a nitrogen gas charge; quality components and engineering ensure long term durability and heat resistance || Coil springs feature cold rolled SAE 9254 rated spring steel for strength and durability; premium quality strut mounts are designed to eliminate transfer of harmonic resonance to the vehicle body || Struts and springs are tuned specifically to each vehicle application to provide OE levels of comfort and stability regardless of road conditions or speed || Compatible with select vehicles (verify fitment details with fit checker above)
Number on catalog scheme: 7
 

Compatible models:

Mariner entire parts catalog list:

7050412YD 1991,1992,1993,1994,1995,1996
7060412ET 1996
7075312SD 1990,1991,1992,1993

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     8T-0914     Guide Pin     2    
B     121-7705     Stud Assembly     4    
C     200-5958     Wear Sleeve Installer     1    
D     5P-8245     Hard Washer     4    
E     1F-7958     Full Nut     4    
F     4C-9507     Retaining Compound     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The crankshaft adapter must be installed on the crankshaft in order to install the wear sleeve. If the crankshaft adapter was removed, Steps 1 through 4 describe installation of the crankshaft adapter. If the crankshaft adapter was not removed, go to Step 6.
Illustration 1 g00633265
Typical example
Install Tooling (A) into the rear of the crankshaft.
Make sure that the arrow on the crankshaft adapter will point in the direction of the crankshaft rotation when the crankshaft adapter is installed. Attach a suitable lifting device to crankshaft adapter (1). Lift the crankshaft adapter onto Tooling (A). The crankshaft adapter weighs approximately 77 kg (170 lb).
Illustration 2 g00633171
Slide crankshaft adapter (1) toward the crankshaft. Install bolts (2) that attach the crankshaft adapter to the crankshaft.
Remove Tooling (A) from the crankshaft.
Illustration 3 g00633181
(B) Stud assembly (C) Wear sleeve installer (D) Hard washer (E) Full nut
Install Tooling (B) into two of the holes in the rear housing. Bolts (3) for the adapter of the crankshaft seal will be installed in these holes later.
Place a new wear sleeve into Tooling (C). Make sure that the arrow on the outside of the wear sleeve will point in the direction of the crankshaft rotation when the wear sleeve is installed.
Apply Tooling (F) to the inside diameter of the wear sleeve.
Place Tooling (C) and the wear sleeve onto Tooling (B). Install Tooling (D) and Tooling (E) onto Tooling (B) .
Tighten the nuts for Tooling (E) evenly in order to press the wear sleeve onto the crankshaft adapter. Press the wear sleeve onto the crankshaft adapter until the wear sleeve contacts the shoulder of the adapter.
Remove Tooling (E), Tooling (D), Tooling (C), and Tooling (B) .Installation of the Rear Seal
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1U-6241     Seal Installer        
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The Tooling (A) is packaged with the new seal and adapter assembly. The seal installer helps to protect the seal. If the seal installer is separated from the seal prior to installation of the seal, the seal can be easily damaged. Do not remove the seal installer from the seal.Note: Do not apply any lubricant to rear seal (2). Do not touch the rear seal when you handle the adapter and seal assembly. Be careful not to damage the rear seal.
Illustration 4 g00634136
Section view of the rear seal and adapter assembly
Use clean engine oil to lubricate O-ring seal (1) on the outer diameter of the adapter.
Illustration 5 g00633173
Typical example
Install two 3/8-16 NC guide bolts (5) into the rear housing.
If a seal is installed on


Parts throttle Mariner:

9591
 
9591 THROTTLE SHAFT (UPPER/LOWER)
7075312ND, 7075312SD, 7075717, 7100412NC
9593
 
9593 THROTTLE VALVE (WME-1/WME-6)
7050412YD, 7060412ET, 7075312ND, 7075312SD, 7075717
98887
 
98887 THROTTLE LINK
7075312ND, 7075312SD, 7075717, 7100412NC
19270
 
19270 THROTTLE SHAFT, Center
7075312ND, 7075312SD, 7100412NC
812885 2
 
812885 2 THROTTLE CAM
7050302ED, 7050412YD, 7060412ET
12018A 4
 
12018A 4 THROTTLE TUBE
7050302ED, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075D73ZY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412C
42946 1
 
42946 1 THROTTLE LEVER
70432037D, 7050302ED, 7055207GD, 7060412ET, 7075217CD
12019A 1
 
12019A 1 THROTTLE CABLE KIT
7050302ED, 7055207GD, 7055207HB, 7055207TF, 7060412ET
Back to top