825204 3 Mariner THROTTLE LINK


825204 3 THROTTLE LINK Mariner 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET THROTTLE
825204 3 THROTTLE LINK Mariner
Rating:
93

Buy THROTTLE LINK 825204 3 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

Mariner entire parts catalog list:

70432037D 1997,1998
7043213HD 1999,2000,2001,2002,2003,2004
7043213TD 2005
7043302TD 2005
7043412TB 2005,2006
7043412TD 2005
7050302ED 1996,1997
7050312TB 2005
7050312UB 2006
7050412TB 2005
7050412TD 2005
7050412UB 2006
7050412YD 1991,1992,1993,1994,1995,1996
7055207GD 1998
7055207HB 1999,2000,2001,2002,2003,2004
7055207TF 2005,2006
7060412ET 1996

Information:


Table 1
Tools Needed     Quantity    
9S-9082 Engine Turning Tool     1    
Illustration 1 g00284801
Location of timing pins (typical example) (1) Timing hole (2) Timing pin
Remove rear camshaft covers from both sides of the engine.
Refer to Testing and Adjusting, "Finding the Top Center Position for the No. 1 Piston".Note: When the timing bolt is installed in the flywheel, it is not necessary to remove the No. 1 valve cover in order to find the compression stroke. Both rear camshaft covers must be removed in order to check the timing.
When the timing bolt is installed in the flywheel, look at the rear end of the camshaft. If the timing ring is visible, then the No. 1 piston is on the compression stroke. If the timing ring is not visible, feel the back of the camshaft for the groove. If the groove is at the back of the camshaft, the flywheel must be turned by 360 degrees in order to put the No. 1 piston on the compression stroke.
Illustration 2 g00284802
Installation of timing pins (typical example) (2) Timing pin (3) RH Camshaft
When the timing bolt is installed in the flywheel and the No. 1 piston is on the compression stroke, remove timing pins (2) from the storage positions.
Install timing pins (2) through timing holes (1) in the engine block. Install timing pins (2) into the groove in camshaft (3) on each side of the engine. In order to time the engine correctly, the timing pins must fit into the groove of each camshaft.If the timing pins do not engage in the grooves of both camshafts, the engine is not in time, and one or both camshafts must be adjusted.
Proceed to the "Timing Adjustment" procedure.
If a camshaft is out of time more than 18 degrees (approximately 1/2 the diameter of timing pin out of groove), the valves can make contact with the pistons. This will cause damage that will make engine repair necessary.
Timing Adjustment
Table 2
Tools Needed     Quantity    
9S-9082 Engine Turning Tool     1    
1P-0820 Hydraulic Puller     1    
8B-7548 Push-Puller Tool Group     1    
8B-7559 Adapter     2    
5H-1504 Hard Washer     3    
9U-6600 Hand Hydraulic Pump     1    Note: Before any timing adjustments are made, make sure that adjustments are necessary. Refer to "Timing Check".After the timing check procedure is completed, the timing bolt will be engaged in the flywheel with No. 1 piston at the top center (TC) position.
Illustration 3 g00662258
Rocker arm shaft assembly (1) Bolt (2) Rocker Shaft
Remove all valve covers on the side of the engine with the camshaft that needs adjustment. Disconnect the ignition wiring from the ignition transformer and remove the ignition transformer. Loosen bolts (1) that hold rocker shaft (2) to the valve cover bases until all rocker arms are free from the valves.Note: The above procedure must be done before the camshaft drive gear is pulled off the camshaft taper.
Illustration 4 g00662269
Left rear (3) Cover (4) Speed/Timing sensor
Remove camshaft gear cover (3) from the rear of the engine. If the left rear camshaft gear must be removed, remove speed/timing sensor (4) .
Illustration 5 g00662337
Rear gear group (5) Gear (left camshaft drive) (6) Idler gear (7) Speed/Timing ring (8) Gear (right camshaft drive) (9) Washer (10) Bolt (11) Bolt (12) Plate
To remove the left camshaft drive gear, remove bolt (10) and washer (9). Remove speed/timing ring (7) from the left camshaft.
To remove right camshaft drive gear, remove bolt (11) and plate (12) from the right camshaft.
Illustration 6 g00662446
Removing the camshaft drive gear (A) 1P-0820 Hydraulic Puller (12) 4W-4586 Plate
Use tooling (A) to remove camshaft drive gears (5) and (8) .
Install the three 5H-1504 Hard Washers behind plate (12). This plate holds the camshaft drive gear on the camshaft. Install plate (12) and bolt (11) on the camshaft.
Do not apply more than 41,340 kPa (6,000 psi) of pressure to 1P-0820 Hydraulic Puller. 8B-7559 Adapters are rated at 5 ton each and 1P-0820 Hydraulic Puller is rated at 17 ton at 68,900 kPa (10,000 psi). If too much pressure is applied, the gear may be damaged.


Parts throttle Mariner:

811216
THROTTLE VALVE, 90
811216 THROTTLE VALVE, 90
7050412YD, 7060412ET, 7075312SD
821145
 
821145 THROTTLE LINK
7050412YD, 7060412ET
811218
811219
 
811219 THROTTLE SHAFT (CENTER)
7050412YD, 7060412ET
42946 1
 
42946 1 THROTTLE LEVER
70432037D, 7050302ED, 7055207GD, 7060412ET, 7075217CD
832001A 6
 
832001A 6 THROTTLE SHAFT CABLE
7050302ED, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7100412CD, 7100412HB, 7115412TB
9724 5
 
9724 5 THROTTLE VALVE
70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB
828160A 1
 
828160A 1 THROTTLE CAM
70432037D, 7055207GD
Back to top