74968 1 Mariner THRU BOLT


74968 1 THRU BOLT Mariner 7115473JD, 7135412ED, 7135412HD, 7135412JD, 7150413ED, 7150413HD, 7150413LD, 7150423JD, 7175423HD, 7200413JD, 7200473JD, 7225413LD THRU
74968 1 THRU BOLT Mariner
Rating:
23

Buy THRU BOLT 74968 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Mariner entire parts catalog list:

7115473JD 2000
7135412ED 1996,1997,1998
7135412HD 1999
7135412JD 2000,2001,2002,2003,2004,2005
7150413ED 1996,1997,1998
7150413HD 1999
7150413LD 2002,2003
7150423JD 2000,2001
7175423HD 1999
7200413JD 2000
7200473JD 2000
7225413LD 2002,2003

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
C 248-3311 Holding Fixture 1
D 248-3310 Spanner Wrench 1
E 8H-0663 Bearing Puller Gp 1
F 1U-6396 O-Ring Assembly Compound -
G 7N-8268 Installation Tool 1
H 8H-8581 Feeler Gauge 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01040290
Use Tooling (E) and a suitable press to install assembly (17) on pump shaft (12).
Install bearing cone (23) on the pump shaft.
Install spacer (22) and bearing cups (21) on the pump shaft.
Install bearing cone (20) on the pump shaft.
Illustration 2 g01035607
The splined end of the pump shaft is marked in order to indicate either RH threads or LH threads on the pump shaft. Install bearing locknut (16). Use Tooling (D) on the bearing locknut and tighten the bearing locknut to a torque of 300 30 N m (221 22 lb ft). Note: The torque wrench must be 90 degrees to Tooling (D).
Install set screws (15) and tighten to a torque of 4 1 N m (35 9 lb in).
Illustration 3 g01035690Note: Do not damage the wear surfaces of the carbon ring or the ceramic ring. Do not touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Apply Tooling (F) to the outside diameter of ceramic seal (18). Use Tooling (G) and hand pressure to install ceramic seal (18) into bearing housing (3).
Illustration 4 g01035699
Use Tooling (A) and a suitable press to install lip seal (19) into bearing housing (3). Ensure that the lip is toward the outside. Note: Install the lip seal dry. Install the lip seal within two minutes of removal from the shipping sleeve.
Illustration 5 g01035809
Lubricate pump shaft (12) with clean engine oil. Install the pump shaft in bearing housing (3). Install retainer (11). Install socket head bolts (10) and tighten to a torque of 12 3 N m (106 27 lb in).
Illustration 6 g01035829
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Note: Do not damage the wear surfaces of the carbon ring or the ceramic ring. Do not touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Remove spring (14) from ceramic seal (13).
Apply Tooling (F) to the inside diameter of ceramic seal (13). Use hand pressure and the tool that is supplied with the water pump seal group to install the ceramic seal. The face of ceramic seal (13) should make light contact with ceramic seal (18).
Install spring (14).
Lubricate pump shaft (12) on bearing housing (3) with clean engine oil. Position impeller (9) on the pump shaft.
Illustration 7 g01035846
Place bearing housing (3) on impeller (9). Use a suitable press and press pump shaft (12) into the impeller. Install the impeller so the dimension between the impeller and the pump shaft is 0.000 .076 mm (0.0000 0.0030 inch).
Il


Parts thru Mariner:

823641
 
823641 THRU BOLT
7200413JD, 7225412CD, 7225412HD, 7225413DD, 7225413HD
803005
 
803005 THRU BOLT
7075D73UY, 7090D73RD, 7135473KD, 7135D73RD, 7135D73UY, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7200413UY, 7200413ZY, 7200423UY, 7200473KD, 7200D73MD, 7200D73RD, 7225413LD, 7225413RD, 7225E73MD, 7225V13TF
Back to top