95686 BOLT, THRU Mariner
7050302ED, 7050412YD, 7050716, 7050717, 7060312PC, 7060412ET, 7060524
BOLT
Price: query
Rating:
Number on catalog scheme: 4
Mariner entire parts catalog list:
- STARTER MOTOR ASSEMBLY » 95686
- STARTER MOTOR ASSEMBLY » 95686
- STARTER MOTOR ASSEMBLY (BOSCH) » 95686
- STARTER MOTOR » 95686
- STARTER MOTOR » 95686
- STARTER MOTOR ASSEMBLY (BOSCH) » 95686
- STARTER MOTOR ASSEMBLY » 95686
- STARTER MOTOR ASSEMBLY (BOSCH) » 95686
Information:
Checking Clutch Adjustment
While engaging the clutch to pick up the load, check the clutch adjustment. The clutch should engage with a hard push and distinct snap. If engagement is "soft", adjust the clutch.Adjusting Clutch
1. Stop the engine and remove the clutch inspection cover.
CLUTCH INSPECTION COVER2. Turn the clutch until the lock pin, engaged in the locking ring, is visible.3. Disengage the lock pin and rotate the locking ring clockwise until the lock pin engages the next notch.
PULLING LOCKING PIN4. Test the clutch adjustment. If still too "soft", rotate the ring to the next notch. If the adjustment is too tight-turn the ring back one notch.5. Install the cover.Lubricating Flywheel Clutches And Front Power Take-Off Clutches
(All except D343 oil lubricated clutch)Lubricate the clutch bearings with grease, 1 or 2 strokes each fitting.1. Lubricate the shift level bearings; 1 fitting on each side of the clutch housing.
LUBRICATING SHIFT LEVER BEARINGS2. Lubricate shift-collar and shaft; 1 fitting at top-left of center.
SHIFT COLLAR, SHAFT AND PILOT BEARINGS3. Lubricate the shaft bearing; 1 fitting on top-rear of housing.4. Lubricate pilot bearing; 1 fitting at the end of shaft. If this fitting is not accessible, remove the plug located on the circumference of the shaft near the rear of the housing, and install a fitting.Lubricating D343 Engine Flywheel Clutch
The D343 flywheel clutch main shaft bearing is oil lubricated. The remaining bearings are lubricated with grease.1. Lubricate the shift lever bearings; 1 fitting on each side of clutch housing.
SHIFT LEVER BEARING2. Lubricate the pilot bearing; 1 fitting at the end of shaft. If this fitting is not accessible, remove the plug located on the circumference of the shaft near the rear of the housing, and install a fitting.
PILOT AND SHIFT COLLAR BEARINGS3. Lubricate the shift-collar bearing; 1 fitting at top-left of center.4. Check the main shaft bearing oil reservoir level with engine stopped. Maintain the oil level at the FULL mark on the oil level gauge. Add
While engaging the clutch to pick up the load, check the clutch adjustment. The clutch should engage with a hard push and distinct snap. If engagement is "soft", adjust the clutch.Adjusting Clutch
1. Stop the engine and remove the clutch inspection cover.
CLUTCH INSPECTION COVER2. Turn the clutch until the lock pin, engaged in the locking ring, is visible.3. Disengage the lock pin and rotate the locking ring clockwise until the lock pin engages the next notch.
PULLING LOCKING PIN4. Test the clutch adjustment. If still too "soft", rotate the ring to the next notch. If the adjustment is too tight-turn the ring back one notch.5. Install the cover.Lubricating Flywheel Clutches And Front Power Take-Off Clutches
(All except D343 oil lubricated clutch)Lubricate the clutch bearings with grease, 1 or 2 strokes each fitting.1. Lubricate the shift level bearings; 1 fitting on each side of the clutch housing.
LUBRICATING SHIFT LEVER BEARINGS2. Lubricate shift-collar and shaft; 1 fitting at top-left of center.
SHIFT COLLAR, SHAFT AND PILOT BEARINGS3. Lubricate the shaft bearing; 1 fitting on top-rear of housing.4. Lubricate pilot bearing; 1 fitting at the end of shaft. If this fitting is not accessible, remove the plug located on the circumference of the shaft near the rear of the housing, and install a fitting.Lubricating D343 Engine Flywheel Clutch
The D343 flywheel clutch main shaft bearing is oil lubricated. The remaining bearings are lubricated with grease.1. Lubricate the shift lever bearings; 1 fitting on each side of clutch housing.
SHIFT LEVER BEARING2. Lubricate the pilot bearing; 1 fitting at the end of shaft. If this fitting is not accessible, remove the plug located on the circumference of the shaft near the rear of the housing, and install a fitting.
PILOT AND SHIFT COLLAR BEARINGS3. Lubricate the shift-collar bearing; 1 fitting at top-left of center.4. Check the main shaft bearing oil reservoir level with engine stopped. Maintain the oil level at the FULL mark on the oil level gauge. Add
Parts bolt Mariner:
68298
68298 BOLT, (.375-16 x 3.250), BRACKET TO BOAT
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060507, 7060524, 7060528, 7070509, 7070520, 7080508, 7080629, 7085507, 7090520, 7090529, 7115520, 7115528, 7115529, 7140528, 7140629
66897
66897 BOLT, UPPER MOUNT TO SWIVEL PIN (7/16 X 5 1/4")
70404119D, 7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070509, 7070520
68576
7733
7733 BOLT SET, THRU - PLATE AND FRAME TO RESERVOIR
7045217, 7050200, 7050716, 7060312PC, 7060524, 7070520, 7080629, 7090520, 7115520
8855
8855 BOLT, THRU - END CAP TO END PLATE (1/4-28)
7050716, 7060312PC, 7060524, 7070520, 7075524, 7080629
89673
89673 BOLT, TRANSOM BRACKET TO TRANSOM (5")
7045217, 7050200, 7050716, 7050717, 7060312PC, 7060524, 7070520, 7080629, 7090520, 7115520
31830
31830 BOLT, (.375-24 x 1.75)
7045217, 7050200, 7050716, 7060312PC, 7060524, 7090524, 7115520, 7150629, 7200620, 7250422PD
75379