14182M Mariner VALVE, NEEDLE


14182M VALVE, NEEDLE Mariner 7004201, 7005201, 7005207, 7F08203HF, 7F08261DF VALVE
14182M VALVE, NEEDLE Mariner
Rating:
53

Buy VALVE, NEEDLE 14182M Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$14.99
 

19-07-2021
0.01543235834[0.00] Pound
-: -
MERCURY New Mercruiser Quicksilver OEM Part # 14182M Valve
Number on catalog scheme: 9
 

Compatible models:

Mariner entire parts catalog list:

7004201 1981,1985,1988,1989
7005201 1981,1985,1988,1989
7005207 1977
7F08203HF 1999
7F08261DF 1995,1996,1997,1998

Information:

Introduction
This Special Instruction details instructions to change the present unit injector hydraulic pump for a HEP pump that adds an opposing tapered roller bearing The additional bearing counters gear torsional loads that can lift the rollers off the race and lead to high contact stresses. The new pump design is longer than the current pump. Certain applications will require replacing additional components due to the longer HEP pump. A new high-pressure oil line and adapter are required to connect the pump to the cylinder head.Safety Information
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not operate or work on this engine unless you have read and understand the instructions and warnings in the Operation and Maintenance Manual. Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. Clean up fuel spills immediately.
Cylinder Head Rework Procedure
Note: There is a potential for interference between the new Dual Tapered Roller Bearing (DTRB) Hydraulic Electronic Unit Injector (HEUI) pump and the cylinder head intake flange on C7 ACERT engines built before KHX47176. Engines with build dates after the date above have cylinder heads that do not present this condition. For engines with build dates prior to the date above go to the next step.
Illustration 1 g03389031Test fitting the pump for clearance at location (1) is recommended in Illustration 1. If the new DTRB (HEUI) pump is in contact with the cylinder head after mounting bolts are snugged, modify the cylinder head per the following instructions.Note: Do not modify the HEUI pump. Removing material from the HEUI pump may create an unsafe condition.
Remove HEUI pump and apply suitable protection to the front cover opening and any open fluid lines and fittings to prevent debris entry during this process. Removing the inlet cover group is not required to perform this procedure. If the intake air lines have been disconnected, protect the opening from debris entry.
Illustration 2 g03395855
Scribe a line (2), parallel to the cylinder head top surface, at the center of the port plug. Refer to Illustration 2.
Scribe a line along the edge of the inlet air cover group at edge (3). Refer to Illustration 2.
Scribe a line (4) parallel to line (2) the distance of 48.7 mm (1.9 inch) from line (2) as shown in Illustration 2.


Parts valve Mariner:

91742M
 
91742M VALVE, NEEDLE
7004201, 7005201, 7005207
80204M
 
80204M VALVE SEAT
7005207, 7005227, 7015207
827483M
VALVE-CHOKE
827483M VALVE-CHOKE
7F08203HF, 7F08261DF
825439
 
825439 VALVE-INTAKE
7F08203HF, 7F08261DF
825440
 
825440 VALVE-EXHAUST
7F08203HF, 7F08261DF
809498A 1
 
809498A 1 VALVE ADJUSTER WRENCH
7F08203HF, 7F41452KD, 7F50352HD, 7F50412DD
809496A 1
 
809496A 1 VALVE GUIDE INSTALLER TOOL
7A30302LB, 7A30453VZ, 7A40302UD, 7A40302ZZ, 7A40312UZ, 7A40312ZZ, 7A40412ZZ, 7A41412LB, 7A41452IZ, 7A41452UZ, 7A51412ZZ, 7A51452IZ, 7A60412ZZ, 7A60452IZ, 7E41412ZB, 7E51412ZB, 7E51413VZ, 7E60412ZB, 7E60413VZ, 7E60452IZ, 7E60452ZB, 7F08203HF, 7F10203H
809497A 1
 
809497A 1 VALVE GUIDE REAMER
7A30302LB, 7A40302UD, 7A40312UZ, 7A41412LB, 7A41452UZ, 7A60412ZZ, 7A60452IZ, 7E60452ZB, 7F08203HF, 7F10203HD, 7F13203UB, 7F15201GD, 7F25201GD, 7F25203JB, 7F25203LB, 7F30203HD, 7F30203LB, 7F40203UD, 7F40203ZZ, 7F40213UZ, 7F40452KD, 7F40452LB, 7F41452K
Back to top