80662M Mariner WASHER, MOUNT


80662M WASHER, MOUNT Mariner 7020201, 7025200, 7025207NW, 7025207PW, 7025208CW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 7030320 WASHER
80662M WASHER, MOUNT Mariner
Rating:
18

Buy WASHER, MOUNT 80662M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 14
 

Mariner entire parts catalog list:

7020201 1981
7025200 1980
7025207NW 1988
7025207PW 1989,1990,1991,1992,1993
7025208CW 1994,1995,1996,1997,1998
7025500 1980
7026226 1986,1988
7028207 1977
7028527 1977
7030200 1980
7030205 1985,1986,1987,1988,1989,1990
7030301 1981
7030320 1980,1990,1992

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 9U-6238 Guide Bolt 2
C 8T-3052 Degree Wheel 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Thoroughly clean the top of the cylinder block and the bottom of the cylinder head. Ensure that there is no debris in the cylinder bores.
Illustration 1 g00942889
Install cylinder head gasket (3) on dowels (4) on top of the cylinder block. The cylinder head gasket (3) is stamped "FRONT TOP". Do not use any sealant or compound on the cylinder head gasket.
Install Tooling (B) in the cylinder block in Hole (X).
Illustration 2 g00942891
Install Tooling (A) and a suitable lifting device to cylinder head (2). The weight of the cylinder head is approximately 61 kg (135 lb).
Install cylinder head (2) on the cylinder block. Note: Ensure that the cylinder head is positioned on dowels (4).
Remove Tooling (A). Remove the guide bolts.
Illustration 3 g00942928
Clean the threads of the cylinder head bolts. Inspect the cylinder head bolts. Note: Do Not use bolts if there is any visual reduction in the diameter of the Threads (Y) that has not been engaged with the cylinder block. Use a straight edge to check the bolts.
Lubricate the threads and the shoulder of the cylinder head bolts with clean engine oil before installation.
Install bolts (1) on cylinder head (2). Note: The short bolts are installed in holes that are marked with an "S" (5, 6, 11, 12, 16, 17, 21, 22, 26, 27, 31, and 32).Note: The medium bolts are installed in holes that are marked with an "M" (1, 2, 3, 4, 7, 8, 9, 10, 13, 14, 15, 18, 19, 20, 23, 25, 28, and 30).Note: The long bolts are installed in holes that are marked with an "L" (24 and 29).
Illustration 4 g00893273
Tighten bolt (1) through bolt (32) in numerical order to a torque of 110 N m (80 lb ft). Refer to Illustration 4.
Tighten bolt (1) through bolt (32) again in numerical order to a torque of 110 N m (80 lb ft). Refer to Illustration 4.
Illustration 5 g00946758
Use Tooling (C) to achieve the correct final torque. Note: If Tooling (C) is not used, place an index mark on each bolt.
Tighten the cylinder head bolts in numerical order. Refer to Illustration 4.
Turn the bolts that are marked with an "S" an additional 150 degrees.
Turn the bolts that are marked with an "M" an additional 180 degrees.
Turn the bolts that are marked with an "L" an additional 210 degrees.
Connect the harness assembly for the coolant temperature sensor. End By:
Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
Install the water outlet manifold. Refer to Disassembly and Assembly, "Water Outlet Manifold - Install".
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
Install the air inlet manifold. Refer to Disassembly and Assembly, "Inlet Manifold - Install".
Install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".


Parts washer Mariner:

30188
 
30188 WASHER
7004201, 7005201, 7005207, 7005227, 7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7008305, 7010209, 7015207, 7015307, 7015327, 7015529, 7020201, 7020207, 7025200, 7025207NW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030301, 70303
83768M
 
83768M WASHER
7005201, 7005207, 7008204, 7008208, 7008218EW, 7008226, 7008238, 7008248, 7008305, 7008425, 7030320, 7040706, 7040716
82209M
 
82209M WASHER, THROTTLE SHAFT...
7002200, 7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7015207, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025207PW, 7025500, 7026226, 7028207, 7028527, 7030200, 7030205, 7030320, 7040207, 7040507
81806M
 
81806M WASHER, CLAMP BRACKET BOLT...
7008208, 7008218EW, 7008238, 7008247, 7008248, 7008305, 7008425, 7015207, 7015307, 7015327, 7028207, 7028527
74711
 
74711 WASHER, FUEL TANK COVER FASTENING SCREW...
7008204, 7008208, 7008226, 7008238, 7008247, 7008248, 7015207, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7060507, 7060522, 70605
82196M
 
82196M WASHER, PLATE...
7008208, 7008238, 7008247, 7008248, 7015207, 7015307, 7015327, 7020201, 7025200, 7025207NW, 7025500, 7028207, 7028527, 7030200, 7040207, 7040208, 7040328, 7040507, 7048227, 7048321, 7060507, 7060522, 7060528
82201M
 
82201M WASHER
7028207, 7028527
96364M
WASHER KIT
96364M WASHER KIT
7020201, 7025200, 7025500, 7026226, 7028527, 7030200, 7030205, 7030320, 7040202, 7040206, 7040706, 7040716, 7F08261DF
Back to top