81839M Mariner WASHER, STEERING SHAFT - LOWER


81839M WASHER, STEERING SHAFT - LOWER Mariner 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528 WASHER
81839M WASHER, STEERING SHAFT - LOWER Mariner
Rating:
73

Buy WASHER, STEERING SHAFT - LOWER 81839M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Mariner entire parts catalog list:

7048207 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978

Information:


Illustration 1 g00839578
(1) Delivery valve holder (2) Spring (3) Delivery valve (4) Fuel injection pump (5) Drain tube
Remove delivery valve holder (1) for the No. 1 cylinder.Note: Some fuel injection pumps may need to be removed to an upright position in order to remove the fuel delivery valve. Refer to Disassembly and Assembly, "Fuel Injection Pump - Remove".Note: All components of the fuel delivery valve must be kept clean. Keep the components in clean diesel fuel.
Remove delivery valve (3) from the holder.
Reinstall delivery valve holder (1) and spring (2). Tighten the fuel delivery valve to 42 N m (31 lb ft).Note: Fit the fuel injection pump to the engine if the fuel injection pump was removed.
Install drain tube (5) to delivery valve holder (1) for the No. 1 cylinder.
Illustration 2 g00826712
(6) Fuel reservoir (7) Control valve (8) Hose (9) Drain pan (10) Timing mark
Install fuel reservoir (6) with a control valve (7). Install a hose (8) from fuel reservoir (6) to the inlet of fuel injection pump (4). Fill the fuel reservoir with 0.2 L (0.21 qt) of clean fuel.Note: The fuel reservoir should be approximately 152 mm (6 inch) above the fuel injection pump.
Put drain pan (9) below drain tube (5) in order to catch the fuel.
Open control valve (7) for fuel reservoir (6). If the fuel injection pump is set correctly, then the fuel should flow through drain tube (5) .
From the front of the engine, turn the crankshaft in a clockwise direction until the flow of the fuel is reduced to 1 drop for every 7 to 10 seconds. This should be the correct timing mark (10) .
Illustration 3 g00826730
(4) Fuel injection pump (11) Shim
Ensure that the timing mark (10) is correct. Compare the value by timing mark (10) with Table 1.
Table 1
Engine Description     Maximum Rated Engine Speed (RPM)     Injection Timing (BTC)    
C1.5/3013C Genset     1500     14° 1°    
C1.5/3013C Genset     1800     14° 1°    
C1.5/3013C Genset     3000     20° 1°    
C2.2/3024C Genset     1500     15° 1°    
C2.2/3024C Genset     1800     12° 1°    
C2.2/3024C Genset     3000     18° 1°    
If shim (11) must be replaced, remove the fuel injection pump and the shim.The timing will change one degree for each 0.10 mm (0.004 inch) in thickness of the shim. Thicker shims will retard the timing while thinner shims will advance the timing.Install fuel injection pump (4) and a new shim (11) of the correct thickness. Tighten all nuts and bolts to the correct torque. Refer to Specifications for additional information.Note: If a shim is not required, use a thin coat of 4C-9612 Silicone Sealant on the mating surfaces of the fuel injection pump and the cylinder block.
When the timing is correct, remove drain tube (5), fuel reservoir (6), and hose (8) .
Remove delivery valve holder (1). Assemble all of the components of the fuel delivery valve. Install the fuel delivery valve to fuel injection pump (4). Tighten the fuel delivery valve to 42 N m (31 lb ft).
Install all fuel lines in the correct position. Tighten all nuts and bolts to the correct torque. Refer to Specifications for the correct torque.
Install the fuel shutoff solenoid.
Eliminate air from the fuel system.
The engine must be tested on an engine dynamometer in order to check the maximum no-load speed and engine settings after assembly.


Parts washer Mariner:

49221 1
 
49221 1 WASHER, VENT SCREW
7004201, 7005201, 7005207, 7008208, 7008226, 7008305, 7010209, 7015327, 7015529, 7025500, 7026226, 7030205, 7030301, 7040206, 7040207PW, 7055324, 7055524, 7075312ND, 7075312SD, 7075717, 7100412NC, 71354120D, 7135417PD, 7135826, 7150453ND, 7150453PD,
82200M
 
82200M WASHER...
7008208, 7008238, 7008247, 7008248, 7015207, 7015307, 7015327, 7028207, 7028527, 7040207, 7040208, 7040328, 7040507, 7048207, 7048227, 7048321, 7060507, 7060522, 7060528
81811M
 
81811M WASHER
7040207, 7040507, 7048207, 7048227, 7060507, 7060528
81796M
 
81796M WASHER
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83652M
 
83652M WASHER KIT
7040207, 7040208, 7040328, 7040507, 7060507, 7060522, 7060528
81853M
 
81853M WASHER
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324
81701M
 
81701M WASHER, PLUG SCREW
7048207, 7048227, 7060507, 7060528
81866M
 
81866M WASHER, WAVE
7020201, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
Back to top