83457M WASHER, WAVE Mariner
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7F75411JD, 7F75412RD
WASHER
Price: query
Rating:
Compatible models:
Mariner entire parts catalog list:
7040206 1986,1987,1988,1989
7040207 1977
7040207PW 1989,1990,1991,1992,1993
7040208 1978
7040208PW 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998
7040328 1978,1980
7040507 1987
7040706 1986,1990,1992
- TILT LEVER-PIN » 83457M
- TILT LEVER-PIN » 83457M
- CL AMP AND SWIVEL BRACKET-REVERSE LOCK » 83457M
- THROTTLE LEVER AND LINKAGE » 83457M
- THROTTLE LEVER AND LINKAGE » 83457M
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6195 Valve Spring Compressor 1
268-1969 Adapter 1
276-1221 Head 1
B 1U-6396 O-Ring Assembly Compound 1 Start By:
Remove the rocker shaft assembly.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods in the cylinder head to prevent the entry of loose parts into the engine.
Illustration 1 g01335929
Typical Example
Follow Steps 1.a through 1.h to remove the harness assemblies for the electronic unit injectors.
Place a temporary identification mark on connections (1) for harness assembly (4) for electronic unit injectors (2).
Use a deep socket to remove connections (1) from electronic unit injectors (2).
Remove cable straps (3).
Remove bolt (5) (not shown).
Disconnect harness assembly (7) from harness assembly (4).
From the outside of cylinder head (8), push harness assembly (4) inward. Remove the harness assembly from the cylinder head (8).
Remove O-ring seal (6) from harness assembly (4).
Repeat Steps 1.a through 1.g to remove the remaining harness assemblies.
Illustration 2 g03365330
Typical Example
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Follow Steps 2.a through 2.d to position the appropriate piston at top dead center.
Install Tooling (A) in position on the cylinder head to compress a valve spring (11) for the appropriate piston.
Use Tooling (A) to compress valve spring (11) and open the valve slightly. Note: Do not compress the spring so that the valve spring retainer (10) touches the valve stem seal.
Rotate the crankshaft carefully, until the piston touches the valve. Note: Do not use excessive force to turn the crankshaft. The use of force can result in bent valve stems.
Continue to rotate the crankshaft and gradually release the pressure on Tooling (A) until the piston is at the top dead center position. The valve is now held in a position that allows the valve spring to be safely removed. Note: Valve springs must be replaced in pairs for the inlet valve or the exhaust valve of each cylinder. If all valve springs require replacement the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 6, 2 with 5 and 3 with 4. Ensure that all of the valve springs are installed before changing from one pair of cylinders to another pair of cylinders.
Do not turn the crankshaft while the valve springs are removed.
Apply sufficient pressure to Tooling (A) to allow removal of valve keepers (8). Note: Do not compress the spring so that valve spring retainer (9) touches the valve stem seal.Remove valve keepers (9).
Slowly release pressure on Tooling (A).
Remove valve spring retainer (10) and remove valve spring (11).
If necessary, remove the valve stem seals.
Repeat Steps 3 through 6 to remove the remaining valve springs from the appropriate cylinder.
Remove Tooling (A). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft while the valve springs are removed.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose pa
Parts washer Mariner:
83372M
83372M WASHER
7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83376M
81796M
81796M WASHER
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83430M
81870M
81870M WASHER, WAVE
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324
83700M
71055
71055 WASHER, Fuel Connector Screw
7031203GD, 7031207CD, 7031207LF, 7031312TB, 7041203GB, 7045217, 7B25201GF, 7F25201GD, 7F25203JB, 7F25203LB, 7F75411JD, 7F75412RD
19260M