84429M Mariner WASHER


84429M WASHER Mariner 7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528 WASHER
84429M WASHER Mariner
Rating:
93

Buy WASHER 84429M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 22
 

Mariner entire parts catalog list:

7040202 1982,1985,1986
7040206 1986,1987,1988,1989
7040207 1977
7040207PW 1989,1990,1991,1992,1993
7040208 1978
7040208PW 1989,1990,1991,1992,1993,1994,1995,1996,1997,1998
7040328 1978,1980
7040507 1987
7040706 1986,1990,1992
7040716 1986
7048207 1977
7048227 1977
7048321 1981
7055324 1984,1985,1988,1989
7055524 1984,1985
7060507 1977
7060522 1982
7060528 1978

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1857 Retaining Ring Pliers 1
B 1U-6683 Ring Expander 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that all components are clean and free from wear and damage. If necessary, replace any components that are worn or damaged.
Illustration 1 g02319675
If the original piston is assembled, follow Step 2.a through Step 2.e in order to install the piston rings.
Position the spring for oil control ring (3) into the oil ring groove in piston (4). The central wire must be located inside the end of the spring.
Position the oil control ring with the word "TOP" in the upward position. Use Tooling (B) to install oil control ring (3) over the piston and the spring. Note: Ensure that the central wire is 180 degrees from the ring gap.
Use Tooling (B) to install intermediate compression ring (2) into the second groove in piston (4). The word "TOP" must be upward. The chamfer on the inner face must be downward.
Use Tooling (B) to install top compression ring (1) into the top groove in piston (4). The word "TOP" must be upward. Note: Ensure that the top compression ring is installed with Chamfer (W) in the upward position.
Position the piston ring gaps at approximately 120 degrees away from each other. Note: A new piston assembly is supplied with new piston rings.
Illustration 2 g02210673
Illustration 3 g02090053
Removal of the piston pin bushing in the connecting rod must be carried out by personnel with the correct training. Also special machinery is required. For more information refer to your authorized Caterpillar dealer.
If connecting rod assembly (6), bushing (8) and piston pin (7) are replaced, refer to Specifications, "Connecting Rods" for more information.
Lubricate bushing (8) for piston pin (7) in the connecting rod with clean engine oil. Lubricate the bore for the piston pin in piston (4) with clean engine oil.
Place piston (4) on a suitable surface with the crown downward. Position connecting rod (6) with forged Mark (X) to the square boss (14) on the piston. Ensure that slot (13) on the connecting rod is in the correct position. See Illustration 3.
Install piston pin (7) to piston (4). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (A) in order to install circlips (5) to the piston pin bore in piston (4). Note: Ensure that the circlips are seated in the grooves in the piston.
Install upper bearing shell (9) into connecting rod (6). Ensure that the locating tab for the upper bearing shell is correctly seated in slot (13) in the connecting rod.
Install lower bearing shell (10) into connecting rod cap (11). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Fracture split connecting rods should not be left without the connecting rod caps installed. Temporarily install connecting rod cap (11) and bolts (12) to connecting rod (6) when the assembly is out of the engine. Ensure that the etched number on connecting rod cap matches the etched number on connecting rod. Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side. Tighten bolts (12) to a torque of 20 N m (177 lb in).
Repeat Step 2 through Step 10 for the remaining piston and connecting rod assemblies. End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install" for the correct procedure.


Parts washer Mariner:

83372M
 
83372M WASHER
7040202, 7040207, 7040208, 7040328, 7040507, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83376M
 
83376M WASHER
7040207, 7040208, 7040507
81796M
 
81796M WASHER
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
83430M
 
83430M WASHER
7040207, 7040207PW, 7040208PW, 7040507
81870M
 
81870M WASHER, WAVE
7040202, 7040206, 7040207, 7040207PW, 7040208, 7040208PW, 7040328, 7040507, 7040706, 7040716, 7048207, 7048227, 7048321, 7055324
81839M
 
81839M WASHER, STEERING SHAFT - LOWER
7048207, 7048227, 7048321, 7055324, 7055524, 7060507, 7060522, 7060528
98948M
 
98948M WASHER
7048227, 7048321, 7055324
94524M
 
94524M WASHER
7010209, 7015529, 7040202, 7040206, 7040208, 7040328, 7040706, 7040716, 7115F13KD, 7115F13RD, 7115F13UF, 7F75411JD, 7F75412RD, 7F75413TD
Back to top