42579A 3 Mariner BASE ASSEMBLY, Water Pump


42579A 3 BASE ASSEMBLY, Water Pump Mariner 7002201DK, 7115473JD, 71354120D, 7135412AD, 7135412ED, 7135412HD, 7135412JD, 7135417PD, 7135473GD, 7135473HD, 7135473KD, 7135826, 7135D73RD, 7135D73UY, 7135D73ZY, 7150413ED, 7150413HD, 7150413LD, 7150413RD, 7150413UY, 7150413ZY, 7150423JD, 7150453ND, BASE
42579A 3 BASE ASSEMBLY, Water Pump Mariner
Rating:
23

Buy BASE ASSEMBLY, Water Pump 42579A 3 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

Mariner entire parts catalog list:

7002201DK 1995
7115473JD 2000
71354120D 1990,1991
7135412AD 1992,1993,1994,1995
7135412ED 1996,1997,1998
7135412HD 1999
7135412JD 2000,2001,2002,2003,2004,2005
7135417PD 1989
7135473GD 1998
7135473HD 1999
7135473KD 2001,2002,2003
7135826 1986,1987,1988
7135D73RD 2004,2005
7135D73UY 2006
7135D73ZY 2006
7150413ED 1996,1997,1998
7150413HD 1999
7150413LD 2002,2003
7150413RD 2004,2005
7150413UY 2006
7150413ZY 2006
7150423JD 2000,2001
7150453ND 1988
7150453PD 1989,1990
7150629 1979,1980,1982,1984,1985
7175412PD 1989
7175413AD 1992,1993,1994,1995
7175413PD 1989,1990
7175413YD 1991
7175423HD 1999
7175629 1979,1980,1985,1986,1988
7200412PD 1989,1990
7200413JD 2000
7200413UY 2006
7200413ZY 2006
7200423UY 2006
7200620 1980,1982,1983,1984,1985,1986,1988
7220727 1987,1988

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6283 Timing Pin (Crankshaft) 1
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump.
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Finding Top Centre Position for No.1 Piston". Note: The air compressor must be timed with the engine in order to minimize engine vibration.
Illustration 1 g01272266
Typical example
Install Tooling (B) through Hole (X) in the front housing. Use Tooling (B) in order to lock the crankshaft.
Illustration 2 g01250794
Typical example
Disconnect coolant hose (1) and coolant hose (2) from air compressor (4).
Disconnect the air line from port (3) and air line from port (5).
Remove tube assembly (7) from air compressor (4) and from the cylinder block.
Remove bolts (8) and bolts (10) from support bracket (9) and remove the support bracket.
Illustration 3 g01250816
Typical example
Illustration 4 g01250889
Typical example
Support air compressor (4). Remove nuts (13) and remove the air compressor from the front housing.
If necessary, remove studs (12) from the front housing.
Remove O-ring seal (18) from air compressor (4).
If necessary, remove bolts (15) and remove plate (14). Remove O-ring seal (11) from plate (14). Refer to Illustration 3.
If necessary, remove nut (17) and remove the spring washer. Use Tooling (C) in order to remove gear (16) from the crankshaft of the air compressor. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 230-6283 Timing Pin (Crankshaft) 1
D 4C-9506 Retaining Compound 1
E 1U-6396 O-Ring Assembly Compound


Parts base Mariner:

67623
 
67623 BASE
7135826, 7150629, 7175629, 7200620
96146A 6
 
96146A 6 BASE ASSEMBLY, Water Pump
7150629, 7175629, 7200620
14430 3
 
14430 3 BASE
7002201DK, 7031203GD, 7031207CD, 7031207LF, 7031312TB, 70404119D, 7041203GB, 70432037D, 7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7045217, 7050302ED, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7050412YD, 7055207GD, 7055207HB,
90728
 
90728 BASE
7200620
13170T
13170A 1
 
13170A 1 BASE, FUEL FILTER
7175413AD, 7175413PD, 7175413YD
95239
 
95239 BASE
7002201DK, 7002201SK
811597
BASE
811597 BASE
7002201DK, 7002201SK
Back to top