42461A 1 Mariner WEAR SLEEVE ASSEMBLY


42461A 1 WEAR SLEEVE ASSEMBLY Mariner 7050302ED, 7050412YD, 7055207GD, 7055207HB, 7055207TF, 7060412ET, 7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075717, 7075D73UY, 7075D73ZY, 7090412TB, WEAR

Buy WEAR SLEEVE ASSEMBLY 42461A 1 Mariner genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$27.31
 

02-07-2023
0.0154[0.01] Pounds
-: -
New Mercury Mercruiser Quicksilver Oem Part # 42461A 1 Sleeve/Ring Kit
Number on catalog scheme: 22
 

Mariner entire parts catalog list:

7050302ED 1996,1997
7050412YD 1991,1992,1993,1994,1995,1996
7055207GD 1998
7055207HB 1999,2000,2001,2002,2003,2004
7055207TF 2005,2006
7060412ET 1996
7075217CD 1994,1995,1996,1997,1998
7075217HD 1999,2000,2001,2002,2003,2004
7075217TD 2005
7075217UD 2006
70752L7TF 2005
70752L7UF 2006
7075312ND 1988,1989
7075312SD 1990,1991,1992,1993
7075317TB 2005
7075317UB 2006
7075412TB 2005
7075412UB 2006
7075412UY 2006
7075717 1987,1989
7075D73UY 2006
7075D73ZY 2006
7090412TB 2005
7090412TD 2005
7090412TY 2005
7090412UB 2006
7090412UY 2006
7090D73RD 2004,2005
7100412CD 1994,1995,1996,1997,1998
7100412HB 1999,2000,2001,2002,2003,2004
7100412NC 1988,1989,1990,1991,1992,1993
7115412TB 2005,2006
7115F13KD 2001,2002,2003
7115F13RD 2004,2005
7115F13UF 2006
7A41412LB 2002,2003,2004,2005,2006
7A41452IZ 2006
7A41452UZ 2006
7A51412ZZ 2006
7A51452IZ 2006
7A60412ZZ 2006
7A60452IZ 2006
7E41412ZB 2006
7E51412ZB 2006
7E51413VZ 2010
7E60412ZB 2006
7E60413VZ 2010
7E60452IZ 2007
7E60452ZB 2006
7F30203HD 1999,2000,2001
7F30203LB 2002,2003,2004,2005
7F40452KD 2001
7F40452LB 2002
7F41452KB 2001,2002
7F41452KD 2001
7F50352HD 1999,2000
7F50412DD 1995,1996,1997,1998
7F75411JD 2000,2001,2002,2003
7F75412RD 2004,2005
7F75413TD 2005,2006
7F75413ZD 2006

Information:

1. Remove the carbon from the top inside surface of the cylinder liners.2. Turn the crankshaft until two pistons are at bottom center.3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. Put identification on each bearing cap so it will be installed on the correct connecting rod. 4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2).
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed. Do not damage the cooling tubes when the pistons are removed.
5. Do Steps 1 through 4 for the remainder of the pistons.Install Pistons
1. Be sure that the pistons are installed with flat surfaces (2) of the connecting rods toward each other and the chamfered sides (1) toward the crankshaft. 2. Put clean engine oil on the piston rings and cylinder liners.3. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (3) with tool (A). For more detail about checking bearing clearances and installation of connecting rod bearings, see the topic, REMOVE AND INSTALL CONNECTING ROD BEARINGS.4. Check the bearing clearances with Plastigage.5. Put clean engine oil on bolts (4). Install caps (5) and nuts finger tight. Make sure flat side (6) of each cap is toward the other cap. The chamfered side must be toward the crankshaft. Tighten each nut to a torque of 80 8 N m (60 6 lb ft). Put a mark across the nuts and bolts. Tighten each nut 120° more.
Do not use an impact wrench to tighten the nuts the additional 120°.
6. Check the side clearance between the two connecting rods on the same crankshaft journal. Clearance must be 0.28 to 0.84 mm (.011 to .033 in) for new rods.7. Do Steps 1 through 6 for the remainder of the pistons.End By:a. install oil pumpb. install cylinder headsc. install piston cooling tubesDisassemble & Assemble Pistons
Start By:a. remove pistons
Typical Example1. Remove bearings (3) from the connecting rod and connecting rod cap.2. Remove retainer ring (1) with tool (A).3. Remove pin (2) and connecting rod (4) from the piston. 4. Remove the pistons rings (5) from the piston with tool (B). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning tool. 5. Remove piston skirt (8) from the crown (7). Remove the bearings (9) from the crown. See USE OF PISTON PIN BEARING REMOVAL AND INSTALLATION TOOLS, SPECIAL INSTRUCTIONS, Form No. SMHS7295.6. Heat the connecting rod (4) in an oven to a temperature of 177°-260°C (350°-500°F). Never use a direct flame to heat a connecting rod.7. Put connecting rod (4) in position on the base plate of tooling (C). Put a new rod pin bearing (6) on the adapter part of tooling (C). The old bearing is pushed out by tooling (C) as the new bearing is installed.8. Use tooling (C) to push the new bearing into the connecting rod until the push adapter of tooling (C) makes full contact with the connecting rod surface.9. Use a pin boring machine to make the rod pin bearing the correct size. The bore in the new rod pin bearing must be 50.830 0.008 mm (2.0012 .0003 in).10. Check the clearance between the ends of the piston rings. See PISTONS AND RINGS in SPECIFICATIONS.11. Install bearings (9) in piston crown (7) and install skirt (8). The depth of bearings are 1.0 0.1 mm (.039 .004 in) from the inside edge of the crown boss. Make sure the holes in the bearings are lined up with the holes in the crown. 12. Install the oil ring spring in the oil ring groove of the piston. The oil ring is to be installed over the spring with the oil ring end gap 180° from the oil ring spring point.13. Install the oil ring on the piston with tool (B).14. Install the second (intermediate) piston ring with the side that has the identification "UP-2" toward the top of the piston with tool (B).15. Install the top ring with the side marked "UP-1" toward the top of the piston with tool (B). After the installation of all three piston rings put the piston rings in position so the end gaps are 120° apart.16. Put the piston in position on connecting rod (4). Put clean engine oil on pin (2) and install the pin. Install retainer rings (1) with tool (A). Make sure the retainer rings are in the grooves of the piston.17. Install bearings (3) in the connecting rod and connecting rod cap.End By:a. install pistons


Parts wear Mariner:

78661 1
 
78661 1 WEAR SLEEVE
7075217CD, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075312ND, 7075312SD, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7075717, 7075D73UY, 7075D73ZY, 7090412TB, 7090412TD, 7090412TY, 7090412UB, 7090412UY, 7090D73RD, 7100412CD,
14310A 1
 
14310A 1 WEAR SLEEVE INSTALLATION TOOL
70432037D, 7055207GD, 7075217CD, 7100412CD
14310T 1
 
14310T 1 WEAR SLEEVE INSTALLATION TOOL
7043213HD, 7043213TD, 7043302TD, 7043412TB, 7043412TD, 7050312TB, 7050312UB, 7050412TB, 7050412TD, 7050412UB, 7055207HB, 7055207TF, 7075217HD, 7075217TD, 7075217UD, 70752L7TF, 70752L7UF, 7075317TB, 7075317UB, 7075412TB, 7075412UB, 7075412UY, 7090412T
Back to top