816874 Mariner WING NUT

Table 1
Diagnostic Trouble Codes for ARD Pilot Fuel Pressure High    
J1939 Code    Code Description    Comments    
3480-15     Aftertreatment #1 Fuel Pressure #1 : High - least severe     There are Enhanced Troubleshooting Indicators for these codes.    
3480-16     Aftertreatment #1 Fuel Pressure #1 : High - moderate severity    
Table 2
Required Tools    
Tools Required for Use with an 11/16 in Fitting    
Part Number     Description     Qty    
8T-8902     Tee     1    
228-7089     O-Ring Seals     2    
Tools Required for Use with a 9/16 in Fitting    
Part Number     Description     Qty    
7X-2444     Swivel Tee     1    
214-7568     O-Ring Seals (Tee)     2    
Tools Required for Use with Both Sizes of Fitting    
Part Number     Description     Qty    
6V-3965     Fitting     1    
3J-1907     O-Ring Seals     2    
8T-0855     Pressure Gauge     1    
6V-4144     Quick Connect Coupler     1    
Optional Tools    
Part Number     Description     Qty    
177-7860     Hose As     1    
177-7861     Hose As     1    
177-7862     Hose As     1    
126-6872     9/16 inch Tee     1    
8C-3309     11/16 inch Tee     1    
Illustration 1 g01985893
Aftertreatment Regeneration Device (ARD) Fuel Pump (1) Electrical connector (2) Fuel outlet (3) Fuel return to tank (4) Fuel inlet (5) Fuel inlet (alternative) (6) Fuel inlet (alternative)
Illustration 2 g03017616
Components on the ARD combustion head (7) Pilot filter connector (8) ARD combustion head (9) Metal part of heater wire (10) Insulated part of heater wire
Illustration 3 g03018201
ARD Fuel Manifold (11) Pilot fuel control valveNote: After using the electronic service tool to clear a 3480-xx diagnostic trouble code, the keyswitch must also be cycled.Test Step 1. Find the Enhanced Troubleshooting Indicator (ETI)
Establish communication between the electronic service tool and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
Record the ETI code.Results:
The ETI code was a 2 or 3. - Repair: Refer to Troubleshooting, "ARD Fuel Supply - Test" for troubleshooting information.STOP
The ETI code was not a 2 or 3. - Proceed to Test Step 3.Test Step 2. Inspect the Fuel LinesInspect the fuel lines between the ARD fuel pump and the ARD combustion head for kinks or damage.Expected Result:The fuel lines are not kinked or damaged.Results:
The fuel lines are not kinked or damaged. - Proceed to Test Step 3.
A fuel line is kinked or damaged. - Repair: Replace the kinked or damaged fuel line and then check that the fault has been eliminated. If the fault is still present, proceed to Test Step 3.Test Step 3. Check the ARD Fuel Pump
Turn the engine "OFF".
Disconnect the fuel outlet line (2) from the ARD fuel pump. Refer to Illustration 1.
Install the applicable tools that are listed in Table 2 to the outlet port of the pump.
Connect the fuel outlet line (2) to the swivel tee.
Connect the electronic service tool. From the menu, select "Diagnostics" and then select "Diagnostic Tests". From the diagnostic tests menu, select "Override Parameters".
Start the engine.
On the electronic service tool, select "Aftertreatment Fuel Pump Relay Override" in order to activate the pump.
Record the pressure from the pressure gauge.
Deactivate the override.
Turn the keyswitch to the OFF position.
Remove the tools and then reconnect the fuel outlet line to the ARD fuel pump.Note: Use a new O-ring seal on the fuel outlet line.The pressure must be within specifications. The pump pressure must be 1900 120 kPa (275.5 17.4 psi).Results:
The pump pressure is above the specification. - Proceed to Test Step 4.
The pump pressure is within specifications. - If a 3480-15 code with an ETI of 6 is present, proceed to Test Step 4.
The pump pressure is within specifications. - If a 3480-15 code with an ETI of 1 is present, proceed to test step 7.
The pump pressure is within specifications. - If a 3480-16 code is present, proceed to Test Step 4.Test Step 4. Check the Current Flow Through the Nozzle Heater
Verify that the engine is off.
Connect a suita