11439M Mariner WIRE, LEAD


11439M WIRE, LEAD Mariner 7008204, 7008208, 7008218EW, 7008226, 7008425 WIRE
11439M WIRE, LEAD Mariner
Rating:
13

Buy WIRE, LEAD 11439M Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Mariner entire parts catalog list:

7008204 1984,1985,1986
7008208 1978
7008218EW 1996,1998
7008226 1986
7008425 1985,1989,1990,1991,1992,1993,1994,1995,1997

Information:

Recommended Repairs
Verify that the Load is Not Excessive
Interview the operator. Verify that the load is within the specification of the engine and the drive train.Check the Brakes
A brake that drags can limit the vehicle's speed. Check the vehicle's brake system for proper operation.Check Programmable Parameters
Certain programmable parameters may limit vehicle speed. Use the Caterpillar Electronic Technician (ET) to check the following programmable parameters:
Vehicle Speed Limit (VSL)
Lower Gears Engine RPM Limit
Intermediate Gears Engine RPM Limit
Gear Down Protection Engine RPM Limit
VSL Protection
"PTO Top Engine Limit" with the PTO on/off switch in the ON position
"Maximum PTO Vehicle Speed" with the PTO on/off switch in the ON position
Soft Vehicle Speed LimitSet each parameter to the maximum value one at a time and determine whether the problem is corrected.Note: Programming the "Soft Vehicle Speed Limit" to "No" may eliminate the complaint.Check the Vehicle Speed Circuit
Use Cat ET to monitor the vehicle speed signal while the vehicle is operated. Verify that the vehicle speed signal is reasonably close to the vehicle's actual speed. Refer to Troubleshooting, "Vehicle Speed - Calibrate", if necessary.Check the Electronic Control System
Use Cat ET to monitor the fuel position, the rated fuel limit, and the FRC limit. While the vehicle is operating under full load, the parameters should meet the following conditions:
The fuel position is equal to the rated fuel limit.
The fuel position is less than the FRC limit.If the fuel position is equal to the rated fuel limit and the fuel position is less than the FRC limit, the electronic control system is operating correctly.If the fuel position is not equal to the rated fuel limit and/or the fuel position is not less than the FRC limit, check the intake manifold pressure on Cat ET when the engine is not running. The intake manifold pressure should be 0 kPa (0 psi).Check the Accelerator Pedal Position Sensor
Use Cat ET to monitor the status of the accelerator pedal position sensor. Operate the engine at high idle with the vehicle in neutral. If the engine cannot reach the programmed "Top Engine Limit", check the duty cycle for the accelerator pedal position sensor. Refer to the circuit test Troubleshooting, "Sensor Signal (PWM) - Test".Check the Systems on the Power Train Data Link
A system that is connected to the power train data link may be limiting the vehicle's speed. These systems include the brakes and the transmission.Note: You may need a special service tool in order to monitor the other modules on the J1939 data link. Obtain the necessary equipment, when possible. Monitor the appropriate parameters while the vehicle is experiencing problems. Determine if the systems are limiting the engine's speed.Determine if the condition is normal operation. Refer to the vehicle's Original Equipment Manufacturer (OEM) if the condition is not normal operation.Check the Air Inlet and Exhaust System
Check the air cleaner element according to the procedure in the Operation and Maintenance Manual.Check the air inlet and the exhaust system for restrictions. The procedure is in the Systems Operation/Testing and Adjusting manual.Check for aftercooler core leakage. The procedure is in the Systems Operation/Testing and Adjusting manual.Check the Fuel System
Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.Ensure that the fuel system has been primed. The priming procedure is in the Operation and Maintenance manual.Check for air in the fuel system. Also check the fuel pressure. The procedures are in the Systems Operation/Testing and Adjusting manual.Check for a restriction in the fuel supply lines.Check the fuel filters.


Parts wire Mariner:

88809A 5
 
88809A 5 WIRE ASSEMBLY, YELLOW
7006201CD, 7006201HB, 7006201TB, 7008218EW, 7008237, 7010207HB, 7011201TB, 7015201LD, 70152374D, 7020201HB, 7020201NC, 7020201TB, 7020207
99059M
 
99059M WIRE
7008204, 7008208, 7008218EW, 7008226, 7008238, 7008248, 7008425, 7010209, 7015529, 7020201, 7025200, 7025207PW, 7025500, 7026226, 7028527, 7030200, 7030205, 7030301, 7040202, 7040206, 7040207PW, 7040716, 7055524
83257M
 
83257M WIRE COMPLETE, STARTER LOCKOUT
7008208, 7008238, 7008248
96568M
 
96568M WIRE COMPLETE, STARTER LOCKOUT
7008208, 7008218EW, 7008238, 7008248, 7008305, 7008425
Back to top