804018 Mariner WIRE, Throttle

Cat ET Location
Connect to Cat ET.
Select the appropriate ECM.
Select the "Diagnostics" tab.
Select the "Diagnostic Tests" tab.
Select the "Override Parameter" tab. Override Parameters Listed in the Engine ECM Menu
Injection Disable Override
This override is used to turn off the fuel injector circuits in order to stop the engine from running.Active Diagnostic Codes
The purpose of this screen is to show all of the active diagnostic codes. Cat ET Location
Connect to Cat ET.
Select the appropriate ECM.
Select the "Diagnostics" tab.
Select the "Active Diagnostic Codes" tab. Tab Functions At Bottom of Screen
Reset All
This tab will reset all of the active codes.Troubleshoot Code
This tab is currently not available for this engine. Refer to the Troubleshooting guide.Troubleshoot Symptom
This tab is currently not available for this engine. Refer to the Troubleshooting guide.Logged Diagnostic Codes
The purpose of this screen is to show all of the logged diagnostic codes. Cat ET Location
Connect to Cat ET.
Select the appropriate ECM.
Select the "Diagnostics" tab.
Select the "Logged Diagnostic Codes" tab. Tab Functions At Bottom of Screen
Clear
This tab will clear specific codes when highlighted.Clear All
This tab will clear all logged diagnostic codes.Troubleshoot Code
This tab is currently not available for this engine. Refer to the Troubleshooting guide.Troubleshoot Symptom
This tab is currently not available for this engine. Refer to the Troubleshooting guide.Active Event Codes
The purpose of this screen is to show all of the active event codes. Cat ET Location
Connect to Cat ET.
Select the appropriate ECM.
Select the "Diagnostics" tab.
Select the "Events" tab.
Select the "Active Events" tab. Tab Function At Bottom of Screen
Reset All
This tab will reset all of the active codes. Some of the event codes will "latch" to active status. Repairing the system will not "unlatch" the event codes and the event codes must be reset with Cat ET.Logged Event Codes
The purpose of this screen is to show all of the logged event codes. Cat ET Location
Connect to Cat ET.
Select the appropriate ECM.
Select the "Diagnostics" tab.
Select the "Events" tab.
Select the "Logged Events" tab. Tab Functions At Bottom of Screen
Clear
This tab will clear specific codes when highlighted.Clear All
This tab will clear all logged diagnostic codes.Troubleshoot Code
This tab is currently not available for this engine. Refer to the Troubleshooting guide.Troubleshoot Symptom
This tab is currently not available for this engine. Refer to the Troubleshooting guide.Diagnostic Tests
Cat ET diagnostic tests are listed below.Cat ET Location
Connect to Cat ET.
Select the appropriate ECM.
Select the "Diagnostics" tab.
Select the "Diagnostic Tests" tab. Diagnostic Tests Listed in the Engine ECM Menu
Injector Solenoid Test
The purpose of the injector solenoid test is to diagnose injector wiring and injector solenoid functionality.This test identifies an open circuit or a short circuit in the circuit for the injector solenoids. The test activates the injector solenoids one at a time while the engine is not running. A good solenoid will create an audible click when the solenoid is activated. Cat ET indicates the status of the solenoid as "OK", "Open", or "Short".Cylinder Cutout Test
The cylinder cutout test allows one cylinder or multiple cylinders to be cut out. The cylinder cutout test is useful when troubleshooting poor engine performance or a suspected injector failure.The cylinder cutout test disables the injector by not providing the injector pulse to the solenoid. The cylinder cutout test can be performed on one injector or multiple injectors at once.Wiggle Test
The purpose of the Wiggle Test is to detect intermittent electrical faults in electronic control systems. The Wiggle Test function allows the user to determine if there is an intermittent wiring problem. The test will indicate (by changing the value reading) which parameter moved beyond a predetermined range while wiggling the wiring harness, sensor, or connector.This test requires that the engine is OFF and the key switch is in the ON position (or ECM energized and 0 engine speed). If the engine is started with the wiggle test active, the wiggle test will abort.The Wiggle Test will reduce all ECM requirements to trip fault codes, making the diagnostics sensitive. Under normal operation some fault codes need multiple occurrences before the code will log. But during this test the fault codes will trip the first time.The mechanic wiggles and shakes the wiring to see if codes go active. An audible alarm is also activated if the ECM sees any parameter change state electrically. Once the test has ended, the ECM returns to normal diagnostic state.Calibrations
Cat ET calibrations are listed below.Cat ET Location
Connect to Cat ET .
Select the appropriate ECM.
Select the "Service" tab.
Select the "Calibrations" tab.