14614A 1 Mariner WIRING HARNESS (INTERNAL)


14614A 1 WIRING HARNESS (INTERNAL) Mariner 7050717, 7060312PC WIRING
14614A 1 WIRING HARNESS (INTERNAL) Mariner
Rating:
13

Buy WIRING HARNESS (INTERNAL) 14614A 1 Mariner genuine, new aftermarket parts with delivery
Number on catalog scheme: 24
 

Compatible models:

Mariner entire parts catalog list:

7050717 1987,1988,1989,1990
7060312PC 1989

Information:

Pump rotation is clockwise as seen from drive end.(1) Thickness of shims: 3N8441 ... 0.38 mm (.015 in.)3N8455 ... 0.25 mm (.010 in.)Use as necessary to get a clearance of 0.18 to 0.23 mm (.007 to .009 in.) between each plate (A) and impeller (B).(2) Oil seal. Put clean engine oil on lip of seal. Install seal as shown.(3) Apply 9S3265 Retaining Compound between shaft and collar.(4) Tighten nut to a torque of ... 95 to 110 N m (70 to 80 lb.ft.)Bend tab of lock in the groove of the nut.(5) Tighten nut to a torque of ... 60 to 70 N m (44 to 50 lb.ft.)If the cotter pin can not be installed, turn the nut clockwise until the nearest slot in the nut is in alignment with the hole in the shaft.(6) Seal assembly: (a) Put clean water inside the seal assembly.(b) With hand pressure, install the seal assembly on the shaft until the carbon face of the seal assembly makes contact with the shiny face of the ceramic seal.(7) Ring and water seal: (a) Put clean water on the seal and ring.(b) With hand pressure, install the seal and ring as a unit in the housing bore. Make sure the shiny face of the seal is toward seal assembly (6).(8) Tighten bolt to a torque of ... 55 7 N m (41 5 lb.ft.) Hit the bolt with a hammer.Tighten the bolt again to ... 55 7 N m (41 5 lb.ft.)(3N7714)
Pump rotation is clockwise as seen from drive end.(1) Oil seal. Put clean engine oil on lip of seal. Install seal as shown.(2) Tighten bolt to a torque of ... 55 7 N m (41 5 lb.ft.) Hit the bolt with a hammer.Tighten the bolt again to ... 55 7 N m (41 5 lb.ft.)(3) Tighten nut to a torque of ... 60 to 70 N m (44 to 50 lb.ft.) If the cotter pin can not be installed, turn the nut clockwise until the nearest slot in the nut is in alignment with the hole in the shaft.(4) Thickness of shims: 3N8217 ... 0.25 mm (.010 in.)3N8218 ... 0.38 mm (.015 in.)Use as necessary to get a clearance of 0.10 to 0.15 mm (.004 to .006 in.) between each plate (A) and impeller (B).(5) Seal assembly: (a) Put clean water inside the seal assembly.(b) With hand pressure, install the seal assembly on the shaft until the carbon face of the seal assembly makes contact with the shiny face of the ceramic seal.(6) Ring and water seal: (a) Put clean water on the seal and ring.(b) With hand pressure, install the seal and ring as a unit in the housing bore. Make sure the shiny face of the seal is toward seal assembly (5).(7) Apply 9S3265 Retaining Compound between shaft and collar at assembly.(8) Tighten nut to a torque of ... 70 to 80 N m (50 to 60 lb.ft.) Bend tab of lock in the groove of the nut.


Parts wiring Mariner:

13988
 
13988 WIRING HARNESS
7050200, 7050716, 7060312PC, 7060524, 7075524, 7090524, 7115520
96271A 2
 
96271A 2 WIRING HARNESS (INTERNAL)
7050716, 7060312PC, 7060524, 7070520
14585A 1
 
14585A 1 WIRING HARNESS, AUTO-BLEND
7045217, 7050717, 7060312PC, 7075524, 7090524, 7115520
813443
 
813443 WIRING HARNESS
7050717, 7060312PC
Back to top