78610A 1 ADAPTOR, OIL FILTER Mercruiser
02287333, 02297343, 03302336, 03307332, 228801
ADAPTOR
Price: query
Rating:
Mercruiser entire parts catalog list:
- REMOTE OIL FILTER » 78610A 1
- OIL FILTER AND ADAPTER » 78610A 1
- REMOTE OIL FILTER ASSEMBLY » 78610A 1
- OIL COOLER, OIL FILTER AND HOSES » 78610A 1
- REMOTE OIL FILTER ASSEMBLY » 78610A 1
- OIL COOLER, OIL FILTER AND HOSES » 78610A 1
- REMOTE OIL FILTER » 78610A 1
Information:
Introduction
Ensure that you read and fully understand the information that follows before ordering any parts or performing any procedures.This Special Instruction contains the procedures to replace the previous engine alternator mounting group with the new engine alternator mounting group. This change will help prevent vibration damage present in the previous alternator mounting groups design.Removal Procedure
Table 1 contains the parts removed to allow for installation of the new components.
Table 1
Item    Qty    Part Number    Part Description    
1     1     0S-1585     Bolt    
2     2     2P-1974     Taperlock Studs    
3     2     6B-6684     Nuts    
4     1     6L-5874     Pulley Adjustment Rod    
5     1     232-6561     Block    
6     1     232-6579     Bracket    
Illustration 1 g03852443
Remove nuts (3) from pulley adjustment rod (4) .
Remove bolt (1) in order to remove the pulley adjustment rod and block (5) .
Remove taperlock studs (2) in order to remove bracket (6) .Installation Procedure
Table 2 contains the parts required for this Special Instruction.
Table 2
Item    Qty    Part Number    Part Description    
1     3     7X-3374     Nuts    
2     1     2B-0947     Bolt    
3     1     054-3788     Washer    
4     2     106-1792     Taperlock Studs    
5     2     437-7746     Mounts    
6     1     444-6549     Rod As    
7     1     444-7009     Rod    
8     1     460-5997     Bracket    
9     1     460-6011     Block    
10     -     207-1601     Rubber Lubricant    
Illustration 2 g03852511
Mount block (9) with rod assembly (6) and secure with bolt (2) .
Install bracket (8) using taperlock studs (4) and the previously removed nuts to the front housing.
Lubricate mounts (5) with rubber lubricant (10) before installation. Assemble the alternator to the support assembly (8) using the bolt, washers, and nut that was previously removed.Note: Place a washer on the inside next to support assembly (8) on the nut side. Refer to Illustration 2 for locations and specifications.Note: Torque the bolt to 105 20 N m (77 15 lb ft).
Assemble adjusting rod (7) and two jam nuts (1) to the rod assembly. Tighten the assembly to the proper torque.Note: Use a backup wrench to secure the rod end (7) when tightening the jam nut against the rod end. Torque the jam nut (16) to 40 N m (30 lb ft)Note: Assemblies in Step 5 are to be assembled hand tight, so that the alternator V belt can be adjusted prior to final torque of the components.
Install the alternator on adjustment rod (7) with one nut (1) on the outside of the alternator.
Install the V-belt and adjust belt tension according to the following procedure.
With both rod adjustment jam nuts (1) loose, release rod block bolt by ? turn.
Drape belt around the pulleys.
Check that the belt fits in the pulley grooves.
Set belt tension (180 +/- 10 lbs).
Torque rod block bolt (2).
Torque outside jam nut (1) while holding the inside jam nut (1) to maintain correct positioning. Torque to 40 N m (30 lb ft).
Ensure that you read and fully understand the information that follows before ordering any parts or performing any procedures.This Special Instruction contains the procedures to replace the previous engine alternator mounting group with the new engine alternator mounting group. This change will help prevent vibration damage present in the previous alternator mounting groups design.Removal Procedure
Table 1 contains the parts removed to allow for installation of the new components.
Table 1
Item    Qty    Part Number    Part Description    
1     1     0S-1585     Bolt    
2     2     2P-1974     Taperlock Studs    
3     2     6B-6684     Nuts    
4     1     6L-5874     Pulley Adjustment Rod    
5     1     232-6561     Block    
6     1     232-6579     Bracket    
Illustration 1 g03852443
Remove nuts (3) from pulley adjustment rod (4) .
Remove bolt (1) in order to remove the pulley adjustment rod and block (5) .
Remove taperlock studs (2) in order to remove bracket (6) .Installation Procedure
Table 2 contains the parts required for this Special Instruction.
Table 2
Item    Qty    Part Number    Part Description    
1     3     7X-3374     Nuts    
2     1     2B-0947     Bolt    
3     1     054-3788     Washer    
4     2     106-1792     Taperlock Studs    
5     2     437-7746     Mounts    
6     1     444-6549     Rod As    
7     1     444-7009     Rod    
8     1     460-5997     Bracket    
9     1     460-6011     Block    
10     -     207-1601     Rubber Lubricant    
Illustration 2 g03852511
Mount block (9) with rod assembly (6) and secure with bolt (2) .
Install bracket (8) using taperlock studs (4) and the previously removed nuts to the front housing.
Lubricate mounts (5) with rubber lubricant (10) before installation. Assemble the alternator to the support assembly (8) using the bolt, washers, and nut that was previously removed.Note: Place a washer on the inside next to support assembly (8) on the nut side. Refer to Illustration 2 for locations and specifications.Note: Torque the bolt to 105 20 N m (77 15 lb ft).
Assemble adjusting rod (7) and two jam nuts (1) to the rod assembly. Tighten the assembly to the proper torque.Note: Use a backup wrench to secure the rod end (7) when tightening the jam nut against the rod end. Torque the jam nut (16) to 40 N m (30 lb ft)Note: Assemblies in Step 5 are to be assembled hand tight, so that the alternator V belt can be adjusted prior to final torque of the components.
Install the alternator on adjustment rod (7) with one nut (1) on the outside of the alternator.
Install the V-belt and adjust belt tension according to the following procedure.
With both rod adjustment jam nuts (1) loose, release rod block bolt by ? turn.
Drape belt around the pulleys.
Check that the belt fits in the pulley grooves.
Set belt tension (180 +/- 10 lbs).
Torque rod block bolt (2).
Torque outside jam nut (1) while holding the inside jam nut (1) to maintain correct positioning. Torque to 40 N m (30 lb ft).
Parts adaptor Mercruiser:
55110
55110 ADAPTOR, CABLE GUIDE TUBE (DUAL)
00014332, 01206002, 01207333, 01321017, 01326013, 01406002, 01407333, 02287333, 02607333, 03301310, 03302336, 03307332, 04706002, 04707333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 30001854, 37011856, 44031854
66626
86069
86029
54785
48652
48652 ADAPTOR, SHIFT CABLE TO SHIFT LEVER
02287333, 03302336, 03307332, 04706002, 04707333, 08986342, 228801
76792
48504A 2