17623 Mercruiser ARMATURE


17623 ARMATURE Mercruiser 00019003, 01321017, 01326013, 03301310, 5000147JS, 5000150DP, 5000165CE, 5111200LP, 5120136JS, 5120150AR, 5120150R1, 5220200AS, 5231100LP, 5232100N1, 5C30150FS, 5E31200N1, 6020006JS, 6211001N1, 6311002NZ, 6315001N1, 6315002NZ, 6416003N2, 6511102N1, 6 ARMATURE
17623 ARMATURE Mercruiser
Rating:
53

Buy ARMATURE 17623 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 17
 

Mercruiser entire parts catalog list:

00019003 1983,1984,1985,1986,1987,1988,1989,1990
01321017 1987
01326013 1983
03301310 1980,1982,1983,1984,1985,1986,1987,1988,1989,1990,1993,1994
5000147JS 1996,1997
5000150DP 1991,1992,1993,1994,1995
5000165CE 1990,1991
5111200LP 1998
5120136JS 1996,1997,1998
5120150AR 1988,1989,1990,1991,1992,1993,1994,1995
5120150R1 1998
5220200AS 1988
5231100LP 1998
5232100N1 1998
5C30150FS 1993,1994,1995,1996,1997,1998
5E31200N1 1998
6020006JS 1996,1997
6211001N1 1998
6311002NZ 1998
6315001N1 1998
6315002NZ 1998
6416003N2 1998
6511102N1 1998
6811001N1 1998
91331015 1985,1986,1987

Information:

Cleanliness
Whenever hydraulic, fuel, lubricating oil or air lines are disconnected, clean the point of disconnection and the adjacent area. As soon as the disconnection is made, cap, plug or tape the line or opening to prevent entry of foreign material. The same recommendations for cleaning and covering apply when access covers or inspection plates are removed.Clean and inspect all parts. Be sure all passages and holes are open. Cover all parts to keep them clean. Be sure parts are clean when installed. Leave new parts in their containers until ready for assembly.Removal And Installation
Unless otherwise specified, all removals should be accomplished using an adjustable lifting beam. All supporting members (chains and cables) should be parallel to each other and as near perpendicular as possible to the top of the object being lifted. When it is necessary to remove a component on an angle, remember that the capacity of an eyebolt diminishes as the angle between the supporting members and the object becomes less than 90°. Eyebolts and brackets should never be bent and should only have stress in tension. A length of pipe and a washer can be used, as shown, to help relieve these stresses on eyebolts.Forged eyebolts are available. Each size eyebolt has a maximum load recommendation.Some removals require the use of lifting fixtures to obtain proper balance and to provide safe handling.If a part resists removal, check to be certain all nuts and bolts have been removed and that an adjacent part is not interfering. Disassembly And Assembly
When assembling an engine, complete each step in turn. Do not partially assemble one part and start assembling some other part. Make all adjustments as recommended. Always check the job after it is completed to see nothing has been overlooked.Lubrication For A Rebuilt Engine
It is very important for a rebuilt engine to have "adequate" (needed) lubrication during the first seconds of operation. A "dry start" (without needed lubrication) on a rebuilt engine or an engine that has been in storage can cause bearing damage.To prevent the possibility of a "dry start" and bearing damage during the first seconds of running, use the 1P540 Flow Checking Tool Group and shop air pressure to pressure lubricate (fill the main oil passage with oil under pressure) all rebuilt engines and all engines that have been in storage.Procedure for Pressure Lubrication
1. Clean the tank of the 1P540 Flow Checking Tool Group thoroughly, and set the pressure regulator to 35 5 psi (240 35 kPa).
Air pressure should not be more than 50 psi (345 kPa) at any time.
2. Put engine oil in the tank. Use a minimum of 30% of the engine oil capacity. For some engines it will be necessary to fill the tank several times to get the correct amount of oil in the engine.3. Connect the tooling to the main oil passage of the engine.4. Add air pressure to the tank, with the regulator set at 35 5 psi (240 35 kPa). Although the tank does have a hand pump, it is difficult to get enough air pressure to do the job with the hand pump. Therefore, use of shop air is recommended.5. Let the engine oil flow into the oil passage under pressure.Fill the crankcase with the correct oil. The amount of oil used in the pressure lubrication procedure must be subtracted from the recommended refill capacity in the Lubrication and Maintenance Guide. If the engine is not going to be used for a long time, do the above procedure again before the first starting.If shop air is not available for charging the tank, the hand pump may be used to get the minimum required pressure.
Do not use the same 1P540 Flow Checking Tool Group for both "pressure lubrication application" and for checking fuel flow. Incorrect cleaning is probable if the tool is used for both fuel and lube oil. Even a minute amount of dirt in the fuel system can cause fuel nozzle failure.
Initial Operation After Engine Reconditioning
The quality of oil control components used in Caterpillar engines is such that, following engine reconditioning (with Caterpillar Service Parts), only an initial operational check is necessary before continued operation in normal service.The purpose of this initial operational check is to: insure that the engine has been assembled properly; determine if proper pressures and temperatures are maintained in the lubrication, cooling and fuel systems; correct any leaks; perform necessary adjustments (such as valve clearance, governor high and low idle speeds, etc.); check the power setting of the engine.To provide a safe, uniform initial operational check, the following procedure is recommended:1. Motor engine at cranking speed until oil pressure is observed.2. Operate engine for 10 minutes at low idle.3. Operate engine for 15 minutes at half-load and 3/4 rated speed.4. Operate engine for 30 minutes at rated load and speed.Service Tools
Puller Assembly (2 or 3 Arm)
Two or three arm puller assemblies can be used to remove gears, bearing cages, hubs, bearings, shafts, etc.
TYPICAL EXAMPLE
1. Puller.
TYPICAL EXAMPLE
1. Puller. 2. Step Plate.
TYPICAL EXAMPLE
1. Puller. 2. Step Plate.Push Pullers
Push Pullers can be used to remove pulleys, gears, shafts, etc., and can be used in a variety of pulling combinations.
TYPICAL EXAMPLE
*1. Adapters. 2. Ratchet Box Wrench. 3. Push Puller. 4. Step Plate. 5. Legs.*Use as required.
TYPICAL EXAMPLE
1. Push Puller. 2. Adapter. 3. Step Plate.
TYPICAL EXAMPLE
1. Ratchet Box Wrench. 2. Push Puller. 3. Reducing Adapter.
TYPICAL EXAMPLE
1. Push Puller. 2. Ratchet Box Wrench. 3. Step Plate. 4. Bearing Pulling Attachment.
TYPICAL EXAMPLE
1. Push Puller. 2. Bearing Cup Pulling Attachment. 3. Reducing Adapter.
TYPICAL EXAMPLE
1. Bearing Pulling Attachment. 2. Push Puller. 3. Reducing Adapter.Bearing Pulling Attachment
Bearing Pulling Attachments can be used with forcing bolts, to remove shafts, bearings, gears, etc. They can be used with Push Pullers to provide a variety of pulling combinations.
TYPICAL EXAMPLE
1. Bearing Pulling Attachment. 2. Forcing Bolts.Bearing Cup Pulling Attachment
Bearing Cup Pulling Attachments are used to remove bearing races or cups, sleeve-type bearings, bearings, seats, etc. and can be used with Push Pullers.
TYPICAL EXAMPLE
1. Screw. 2. Bearing Cup Pulling Attachment. 3. Step Plate.Rules


Parts armature Mercruiser:

2943
 
2943 ARMATURE. FIELD AND FRAME
00014332, 01321017, 03301310, 2140208, 2165208, 2250507, 6030000ES
7729
 
7729 ARMATURE, FIELD AND FRAME
00014332, 01321017, 03301310, 2140208, 2165208, 5220200AS, 91331015
41214
 
41214 ARMATURE
00019003, 01321017, 01326013, 03301310, 5000165CE
9248
 
9248 ARMATURE, FIELD AND FRAME
00019003, 01321017, 01326013, 03301310, 5000165CE
75665
 
75665 ARMATURE
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02602347, 02607333, 02608427, 03302336, 03307332, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 30001854, 32001876, 3701
68606
 
68606 ARMATURE
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02297343, 02607333, 03302336, 03307332, 03308333, 04544347, 08986342, 228801, 260801, 30001854
68607
 
68607 ARMATURE
01206002, 01207333, 01326013, 01406002, 01407333, 02287333, 02297343, 02607333, 03302336, 03307332, 08986342, 228801, 260801
71693
 
71693 ARMATURE
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01854335, 02287333, 02602347, 02607333, 02608427, 03302336, 03307332, 07711346, 08986342, 08987343, 228801, 260801, 30001854
Back to top