58041 Mercruiser BALL, ROCKER VALVE ARM


58041 BALL, ROCKER VALVE ARM Mercruiser 03302336, 03307332, 03308333, 04544347, 06661346, 4052110CR, 44031854, 4454110AS, 474H110AR, 4S42028N1, 4S42028TS, 4S42028TT, 4S42028UT, 4S42028UU, 4S420P8UE BALL
58041 BALL, ROCKER VALVE ARM Mercruiser
Rating:
43

Buy BALL, ROCKER VALVE ARM 58041 Mercruiser genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

Mercruiser entire parts catalog list:

03302336 1986
03307332 1982
03308333 1983,1984,1985,1987
04544347 1987
06661346 1986,1987,1988,1989
4052110CR 1990,1991,1992
44031854 1984
4454110AS 1988,1989,1991,1992
474H110AR 1988,1989,1990,1991
4S42028N1 1998
4S42028TS 1998
4S42028TT 1998
4S42028UT 1998
4S42028UU 1998
4S420P8UE 1998

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 360-8376 Capping Kit 1
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 1 g06143255
Thoroughly clean the area around fuel manifold (6) and relief valve (5).
Remove banjo bolt (1) from banjo connection (3). Remove sealing washer (2) (not shown) and sealing washer (4) (not shown). Use Tooling (A) to cap the banjo connection and plug relief valve (4). Position the assembly of the banjo connection away from fuel manifold (6) and the relief valve.
Use a suitable socket to remove relief valve (5) from fuel manifold (6). Use Tooling (A) to cap the relief valve and plug the fuel manifold.Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High-Pressure Fuel Lines" for safety information.Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Note: Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage.Note: Do not install a relief valve that has not been plugged. All plugs and caps must be left in place until the fuel lines are about to be installed.
Illustration 2 g06143255
Remove the cap from the port in fuel manifold (6).
Immediately clean the threads in fuel manifold (6) for relief valve (5). Ensure that the thread is clean and free from debris. Ensure that the thread in the fuel manifold is free from damage.
Immediately cap the open port in fuel manifold (6) with a new cap after cleaning and inspection.
Remove the cap from the threaded end of relief valve (5). Lubricate the thread of the pressure relief valve with clean fuel.
Remove the cap from the port of fuel manifold (6). Use a suitable socket to install the relief valve (5) into fuel manifold hand tight.
Tighten relief valve (5) to a snug torque of 30 N m (266 lb in). Rotate the fuel pressure relief valve in a clockwise direction for an additional 24 degrees to achieve the final torque.
Remove plug from relief valve (5) and cap from banjo connection (3).
Install a new sealing washer (2) (not shown) onto banjo bolt (1). Install the banjo bolt and the remaining new sealing washer (4) (not shown) to banjo connection (3).
Position banjo connection (3) onto relief valve (5). Tighten the banjo bolt to a torque of 15 N m (133 lb in).
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.


Parts ball Mercruiser:

45712
 
45712 BALL, VALVE COVER
00014332, 02287333, 02607333, 08986342, 2140208, 2165208, 2250507, 228801, 260801, 2888203, 44031854
7005
 
7005 BALL BEARING, DRIVE END FRAME AND ROTOR SHAFT
00014332, 01206002, 01207333, 01326013, 01402414, 01406002, 01407333, 01751347, 01851333, 01854335, 02287333, 02297343, 02602347, 02607333, 02608427, 03302336, 03307332, 03308333, 04544347, 06661346, 07711346, 08986342, 08987343, 228801, 260801, 3000
62780A 1
 
62780A 1 BALL BEARING
00014332, 01207333, 01402414, 01407333, 02287333, 02602347, 02607333, 02608427, 08986342, 08987343, 228801, 257B021JS, 260801, 30001854, 37011856, 44031854, 457B100KS
73393
 
73393 BALL JOINT
02297343, 03307332, 03308333, 04544347, 30001854, 37011856, 44031854, 473B1F0GS
47470
 
47470 BALL BEARING, ENGINE COUPLING
03307332, 03308333, 04544347, 30001854, 37011856, 44031854, 5220200AS, 91331015
57762
 
57762 BALL BEARING, TAILSTOCK (3-5/32" O.D.)
03307332, 03308333, 04544347, 30001854, 37011856, 44031854
32537
 
32537 BALL BEARING, TAILSTOCK (2-27/32" O.D.)
03307332, 03308333, 04544347, 30001854, 37011856, 44031854
Back to top